Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Centrifugal-Dasher Churn: Curved Wings on a Hollow Shaft Throw the Cream at the Wall, a Fixed Disk Turns It Back
Buttercup

Criado por

Buttercup

11. novembro 2026IE
6
0
0
0
0

Centrifugal-Dasher Churn: Curved Wings on a Hollow Shaft Throw the Cream at the Wall, a Fixed Disk Turns It Back

John W. Kellberg of Pittsburgh received US 30,409, dated 16 October 1860, for a churn whose dasher is two plates joined by three curved wings on a hollow shaft. A crank and bevel gearing on the lid spin it fast: the wings throw the cream out against the wall with friction, air is drawn down the hollow shaft through the cream, and a fixed disk above stops the cream and sends what comes over it back to the middle. He wrote that his churn finished in four to six minutes. The patent gives no sizes; every size here is ours.
Intermediário
About 2 days

Instruções

1

How high the dasher throws the cream

A carregar o notebook Jupyter…
2

Air piped to the middle of the cream, a year before

Rohrer pipes air to the middle of a barrel churn. Kellberg draws it down the dasher's own hollow shaft.
3

Read US 30,409

"When the shaft h is made to revolve quickly the curved wings cause the cream to be thrown from the center to the circumference of the churn with so much force as to create a large amount of friction when it is being pressed between the wing or dasher extensions and the sides of the churn, and at the same time a strong current of air is carried through the body of the cream, and any cream that is forced out over the disk i, flows back into the center to be worked over."
4

Print the step m

The step the dasher turns on: 60 mm across, 10 high, with a 10.6 mm hole 9 deep. It sits loose on the bucket's floor. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Dasher: plates k and k', wings l, ribs o and tube h

Cut two 10 mm HDPE plates 256 mm across. Bore the top plate k 20.2 mm at the centre and six 20 mm openings n on a circle 80 mm across. Press a 10 mm stainless rod 20 mm long into the centre of the bottom plate k' so 10 mm stands below it as the pin m. Cut three stainless sheet wings 1.5 mm thick and 105 mm high, with three 15 mm tabs on each long edge; bend the tabs, curve each wing from 30 mm out at the hub to 122 mm out over 70 degrees and on for 30 degrees more nearly along the edge, and screw the tabs to both plates so the wings stand 105 mm between them. Screw three hardwood ribs 10 x 5 mm on the top of k and three under k', radial. Pass a 20 mm stainless tube 313 mm long down through k until its end is flush with k's underside, and hold it with a shaft collar each side of k. The tube is open at the top: it is the air pipe.

Materiais para este passo:

Chapa de PEADChapa de PEAD1 peça
Chapa de aço inoxidávelChapa de aço inoxidável1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tubo de aço inoxidávelTubo de aço inoxidável1 peça
Shaft CollarShaft Collar2 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira30 peças

Ferramentas necessárias:

BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Tesoura de chapaTesoura de chapa
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Serra de arco para metaisSerra de arco para metais
Conjunto de chaves de fendasConjunto de chaves de fendas
6

Body g, disk i and lid f

Use a 20-litre food-grade bucket as the body g. Set the step m on its floor and stand the dasher on it. Cut a 6 mm HDPE disk i to fit the bucket 150 mm up (282 mm across for ours), with a 100 mm opening in the middle, slide it down over the tube and press it until it wedges in the bucket's taper, so it cannot turn. Cut a 12 mm HDPE lid f to the bucket's top with a 32 mm hole, fit the printed bush in it, and screw three hardwood cleats under its edge that touch the wall; fix the lid by a screw through the wall into each cleat, above the cream.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD2 peças
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira9 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
BússolaBússola
Serra tico-ticoSerra tico-tico
Conjunto de brocas de páConjunto de brocas de pá
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
7

Print the lid bush

The bush the tube turns in, fitted in the lid's hole: 32 mm across, 18 high, 20.6 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
8

Print the crown wheel a

The driving wheel a on the crank shaft c: a crown wheel of 42 teeth, module 2.5, 16.2 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
9

Print the pinion b

The pinion b on the tube h: 14 teeth, module 2.5, 14 mm face, 20.4 mm bore. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
10

Stand e, shaft c, wheel a, pinion b and crank d

Pin the pinion b on the tube with its teeth centred 40 mm above the lid. Cut two hardwood posts 50 x 25 x 118 mm, bore them 16.6 mm across 92 mm up, and screw them to the lid either side of the tube, one 60 to 85 mm in front of it and one 25 to 50 mm behind, as the stand e. Run a 16 mm stainless shaft c 180 mm long through them, pin the crown wheel a on it meshing the pinion, hold it with a shaft collar, and pin on a crank d of mild steel flat bar, 100 mm throw, with a hardwood handle.

Materiais para este passo:

Varão de aço inoxidávelVarão de aço inoxidável1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Shaft CollarShaft Collar1 peça
ContrapinoContrapino3 peças
Barra chata de aço macioBarra chata de aço macio1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Parafusos para madeiraParafusos para madeira4 peças
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Limas (lima de mão)Limas (lima de mão)
Torno de bancadaTorno de bancada
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
11

The build in 3D

FreeCAD model of this build, the bucket cut open: the step, the dasher with its two plates, curved wings, openings and ribs on the hollow tube, the fixed disk above it, the lid with its bush and cleats, and the stand with the crank, crown wheel and pinion.
Arquivo de designBLENDCC0 - Free
12

Churn

Before fitting the lid, pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket, so it stands just under the disk i. Fit the lid and pin the pinion. Turn the crank briskly, timing it. When the butter comes, unpin the pinion, take off the lid, lift out the disk and the dasher, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
13

Troubleshooting

Centrifugal-dasher churn troubleshooting.

Flow

Loading...
14

History and honest limits

**John W. Kellberg** of Pittsburg, Allegheny County, Pennsylvania, US 30,409, 16 October 1860, "Churn". He claimed "the dasher and disk, made and operating substantially as described", and wrote that a churn on his plan completed a churning "in from four to six minutes"; we have not tested that. His gears were a bevel wheel and pinion on a cast stand; ours are a printed crown wheel and pinion on wooden posts. The patent does not say how the disk i is fastened; ours wedges in the bucket's taper. The patent gives no sizes; every size here is ours.

Materiais

15

Ferramentas necessárias

18

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...