Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)
Forge

Criado por

Forge

13. novembro 2026NO
8
0
0
0
0

Reversible-Tip Soft-Face Hammer: Domed Rubber Tips Locked in Screw-On Sockets by an Internal Rib (West & Robinson, 1962)

Robert F. West and Walter H. Robinson of Connecticut received US 3,040,792, dated 26 June 1962, for The Stanley Works. A tubular socket screws onto a threaded boss at each end of the hammer's head. A rubber tip, domed at both ends, is pushed into the socket past an internal rib, which bites into it, and its rubber fills short grooves so it cannot turn. The tip can be pulled out and turned round to use its other end. On its first blows the tip's inner face squeezes into an off-centre hole in the boss and forms its own dowel, which stops the socket unscrewing. The patent gives no sizes; every size here is ours.
Avançado
About 2 days

Instruções

1

The tip's proportions

A carregar o notebook Jupyter…
2

Read US 3,040,792

"Upon being subjected to the percussive forces during initial use, some of the plastic material of the inner face 27 of the striking tip 26 will be extruded or forced into the eccentrically located recess 12 in the boss surface 10 to provide a self-forming dowel pin 28 which effectively prevents inadvertent loosening of the threaded connection between boss and mounting socket during use."
3

Turn the head 2

From 35 mm steel bar turn a body 4 80 mm long with a boss 8 20 mm across and 15 mm long at each end; cut M20 threads on the bosses with the die. In each boss's end face drill a recess 12 4 mm across and 4 mm deep, 6 mm off centre. Drill a 20 mm handle eye 6 through the middle in a V-block.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio1 peça
Óleo de corteÓleo de corte1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Goiva de sangrarGoiva de sangrar
Jogo de machos e cossinetesJogo de machos e cossinetes
Porta-cossinetePorta-cossinete
Torno de bancadaTorno de bancada
Engenho de furarEngenho de furar
Bloco em VBloco em V
Jogo de brocasJogo de brocas
Punção de centroPunção de centro
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
Óculos de segurançaÓculos de segurança
4

Turn the sockets 14

From 48 mm bar turn two sockets 30 mm long. Knurl the outside 25. Drill and tap the collar end 18 M20, 8 mm deep. From the other end, before boring, drill four 4 mm holes 20 mm deep centred on a 38 mm circle, for the grooves 24. Bore the aperture 16 38 mm across and 20 mm deep, leaving a rib 22 4 mm wide 10 mm in, turned to 35 mm with 30 degree ramps either side.

Materiais para este passo:

Barra redonda de aço macioBarra redonda de aço macio2 peças
Óleo de corteÓleo de corte1 peça

Ferramentas necessárias:

Torno mecânicoTorno mecânico
Placa de torno de 3 castanhasPlaca de torno de 3 castanhas
Ferramenta de corte para tornoFerramenta de corte para torno
Barra de mandrilarBarra de mandrilar
Goiva de sangrarGoiva de sangrar
Ferramenta de recartilharFerramenta de recartilhar
Engenho de furarEngenho de furar
Jogo de brocasJogo de brocas
Jogo de machos e cossinetesJogo de machos e cossinetes
Desandador de machosDesandador de machos
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
5

Make the tips 26

For each tip, cut nine discs of 4 mm natural rubber sheet 40 mm across and bond them into a stack with contact cement; clamp it overnight. Grind it round to 38.5 mm on the belt sander, then dome both ends: a large curve over most of the face and a small round where it meets the side, the same at both ends, 36 mm long overall.

Materiais para este passo:

Placa de borracha naturalPlaca de borracha natural1 peça
Cola de contactoCola de contacto1 peça

Ferramentas necessárias:

BússolaBússola
X-ato (faca de precisão)X-ato (faca de precisão)
Sargento de barraSargento de barra
Lixadora de rolosLixadora de rolos
Paquímetro digital de 6 polegadasPaquímetro digital de 6 polegadas
6

Assemble

Turn an ash handle to drive into the eye and wedge it. Screw a socket onto each boss hand-tight. Push a tip into each socket, squeezing it past the rib in the vice between soft packing, until its inner dome bears on the boss. Give the first few blows on a wood block: the rubber pushes into the boss's recess and locks the socket. To turn a tip round, pull it out, reverse it and push it back.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Torno de madeiraTorno de madeira
Conjunto de ferramentas de torno (HSS)Conjunto de ferramentas de torno (HSS)
Serra de arco para metaisSerra de arco para metais
Martelo de bolaMartelo de bola
Torno de bancadaTorno de bancada
7

Troubleshooting

Reversible-tip hammer troubleshooting.

Flow

Loading...
8

History and honest limits

**Robert F. West** of Simsbury and **Walter H. Robinson** of West Hartford, Connecticut, assignors to The Stanley Works, US 3,040,792, dated 26 June 1962, filed 31 August 1960. They claimed sockets with an internal portion of reduced cross-section whose surfaces are "inclined to provide ramp surfaces", and symmetrical tips "having end surfaces of convexly curvilinear configuration", removable and "reversible in said sleeves". They list natural rubber, synthetic rubbers, nylon and cellulose esters for the tips; ours are laminated natural rubber. They give proportions but no sizes; every size here is ours.

Materiais

6

Ferramentas necessárias

24

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...