Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Rim-and-Disk Flow Churn: Cream Is Rubbed Past a Turning Disk, Then Falls Through Fixed and Turning Dashers
Buttercup

Criado por

Buttercup

9. novembro 2026IE
3
0
0
0
0

Rim-and-Disk Flow Churn: Cream Is Rubbed Past a Turning Disk, Then Falls Through Fixed and Turning Dashers

Leonardo Westbrook of New York received US 23,968, dated 10 May 1859, for a churn the cream passes through once. It stands over a pail. Cream poured on a turning disk at the top is rubbed between the disk's edge and a rounded rim inside the case, then falls through slats fixed to the case and dashers turning on the spindle, and runs out of the open bottom. A thumb screw under the spindle raises or lowers the disk on the rim. This rung builds it in a 20-litre bucket with its floor cut out.
Intermediário
About 6 hours, plus printing

Instruções

1

The gap at the rim, and the speeds

A carregar o notebook Jupyter…
2

Cream rubbed in one pass, before it

MacNish ran the cream once between a roller and a concave. Westbrook rubs it at a disk's edge, then beats it on the way down.
3

Read US 23,968

"The disk C, being slightly in contact with the rim X X X, as it revolves, rubs the milk or cream as it passes through ... then falling among the numerous dashers is thoroughly churned, before it passes out into the receiving vessel at the bottom."
4

Print the rim segment

A quarter of rim X, half-round, 16 mm wide. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
5

Print the pinion P

The 12-tooth pinion for spindle I's top. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
6

Print the crown wheel P'

The 36-tooth wheel for shaft Q, teeth on its face. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
7

Print the thumb head

The wing head for the thumb screw. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
Arquivo de designSTLCC0 - Free
8

Case A, bars and thumb screw

Cut the floor out of a food-grade 20-litre bucket, leaving a 25 mm flange round the edge (a 230 mm hole). Screw two hardwood bars d d' 340 x 30 x 20 mm across under the flange, halved where they cross, and drill the crossing 10.5 mm. Run an M10 threaded rod 123 mm long up through it with a nut on top of the bars, and glue the printed thumb head on its lower end.

Materiais para este passo:

Balde de 20 litrosBalde de 20 litros1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira8 peças
Varão roscadoVarão roscado1 peça
Porca sextavadaPorca sextavada1 peça
Filamento PETGFilamento PETG1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra tico-ticoSerra tico-tico
SerroteSerrote
FormõesFormões
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
9

Rim X and fixed dashers o

Screw the four rim segments inside the bucket 300 mm above the cut floor, round side inward, with stainless screws from outside. Cut 24 hardwood slats o 50 x 20 x 12 mm and screw them through the wall in three rings of eight, 80, 160 and 240 mm up, each ring turned half a space from the last.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos de máquinaParafusos de máquina32 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon32 peças

Ferramentas necessárias:

SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de chaves de fendasConjunto de chaves de fendas
Fita métricaFita métrica
10

Spindle B, dashers t and disk C

Cut a 40 mm hardwood dowel 290 mm long for spindle B and drill an 11 mm hole 10 mm deep in the middle of its foot (the indentation). Chisel twelve mortises and glue in hardwood dashers t 82 x 20 x 12 mm, four at each of 80, 160 and 230 mm above the foot, each ring turned an eighth from the last, so they pass between the slats' rings. Glue a 12 mm stainless rod 145 mm long 30 mm into the top as spindle I. Cut disk C from 12 mm plywood, 282 mm across, and glue it on the spindle 268 mm above the foot.

Materiais para este passo:

Cavilhas de madeira duraCavilhas de madeira dura1 peça
Tábua de madeira de leiTábua de madeira de lei1 peça
Cola de madeiraCola de madeira1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Placa de contraplacadoPlaca de contraplacado1 peça

Ferramentas necessárias:

SerroteSerrote
FormõesFormões
Berbequim sem fiosBerbequim sem fios
Conjunto de brocas de páConjunto de brocas de pá
Serra tico-ticoSerra tico-tico
Serra de arco para metaisSerra de arco para metais
LixaLixa
11

Beam R, shaft Q and crank K

Lower the spindle in so its foot sits on the thumb screw and the disk on the rim. Cut a hardwood beam R 320 x 44 x 30 mm with a 13 mm hole in the middle, slip it over spindle I onto the rim and screw two cleats under its ends inside the bucket. Fix the pinion on spindle I. Screw two bearing blocks 95 mm tall on the beam, bore them 12.5 mm 70 mm above it, and run a 12 mm stainless rod through them as shaft Q, with the crown wheel meshing the pinion and a hardwood crank K with a dowel handle on the end beyond the bucket.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Parafusos para madeiraParafusos para madeira8 peças
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Parafusos de máquinaParafusos de máquina3 peças
Porca de segurança com anel de nylonPorca de segurança com anel de nylon3 peças
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça

Ferramentas necessárias:

SerroteSerrote
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Conjunto de chaves de fendasConjunto de chaves de fendas
12

The build in 3D

FreeCAD model of this build, the near half of the bucket and rim cut away: the bars and thumb screw, the three rings of slats, the spindle with its dashers and disk on the rim, the beam with spindle I and the pinion, and shaft Q with the crown wheel and crank.
Arquivo de designBLENDCC0 - Free
13

Churn

Stand the churn on its bars over a clean pail or tub. Turn the thumb screw until the disk just touches the rim. Turn the crank and pour about 8 litres of heavy cream at about 15 °C slowly onto the disk, checked with the thermometer; it runs past the rim, through the dashers and into the pail. How many passes it needs is not given: pour it through again until the butter comes, timing it. Then pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater8 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Recipiente de armazenamento de grau alimentarRecipiente de armazenamento de grau alimentar
Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
14

Troubleshooting

Rim-and-disk churn troubleshooting.

Flow

Loading...
15

History and honest limits

**Leonardo Westbrook** of New York, US 23,968, 10 May 1859, "Churn". He did not claim friction, compression or level turning dashers among fixed ones as such, only the rim with the disk working over it, with the dashers and the thumb screw. His only size is the rim, 1/2 to 3/4 in. wide. We use the plain spindle he allows instead of his cone-shaped one, and a crown wheel and pinion for his two pinions; every other size and material is ours.

Materiais

15

Ferramentas necessárias

16

Ficheiros de design

5

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...