Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

Funnel-Tube Atmospheric Churn: Trailing Funnels on a Fast Cross Draw Air Down Slanting Tubes Into the Cream
Loren J. Wicks of Racine, Wisconsin, received US 23,208, dated 8 March 1859, for an atmospheric churn. A crank turns a wheel cogged on its side, which spins an upright shaft fast. Near its foot the shaft carries a cross with a funnel on each arm, mouth trailing; four slanting tubes run from the funnels up to the shaft near its top. As the funnels draw away from the cream, air is sucked down the tubes and bubbles up through it. The top has gauze-covered openings for air and for watching the cream.
This rung builds it in a square food container with printed gears and cross.
Avançado
About 6 hours, plus printing
Instruções
1
1
Speeds at the tubes' two ends
Speeds at the tubes' two ends
A carregar o notebook Jupyter…
2
2
Air into the cream, before it
Air into the cream, before it
Bump pumped air in with a hollow dasher. Wicks lets turning funnels draw it in with no valve.
3
3
Read US 23,208
Read US 23,208
"As the funnels recede from the cream or milk a vacuum is produced in the tubes j, j, j, j, and the external air rushes in immediately at the tops of the tubes and is conveyed through them to the bottom of the churn, where it escapes and rises through the cream to the top of the churn again."
4
4
Print the cross i
Print the cross i
The cross with four slanting tube sockets and the funnels k on the arms' sides. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
5
5
Print the collar
Print the collar
The collar that holds the tubes' tops round the shaft. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
6
6
Print the socket
Print the socket
The foot bearing for shaft G. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
7
7
Print the pinion F
Print the pinion F
The 12-tooth pinion for the top of shaft G. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
8
8
Print the wheel E
Print the wheel E
The 204 mm wheel with 60 teeth on its side. Print it flat, teeth up. PETG, 0.2 mm layers, 40 % infill, 4 walls; wash before first use.
9
9
Body A and the ventilating top
Body A and the ventilating top
Use a square food-grade container about 300 x 300 x 320 mm. Cut a 12 mm plywood top 320 mm square with a 13 mm hole in the middle and two openings 70 x 80 mm beside it; staple wire mesh over the openings (gauze D) and screw two hardwood cleats underneath so the top sits square on the rim. Screw the socket to the middle of the container's floor with an M4 screw and lock nut.
Materiais para este passo:
Recipiente de armazenamento de grau alimentar1 peça
Placa de contraplacado1 peça
Rede metálica1 peça
Tábua de madeira de lei1 peça
Parafusos para madeira8 peças
Parafusos de máquina1 peça
Porca de segurança com anel de nylon1 peça
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra tico-tico
Berbequim sem fios
Jogo de brocas
Tesoura de chapa
Conjunto de chaves de fendas
Fita métrica10
10
Shaft G, cross, tubes and collar
Shaft G, cross, tubes and collar
Cut a 12 mm stainless rod 373 mm long for shaft G. Fix the cross on it 20 mm above its foot and the collar 258 mm above its foot, each with an M4 screw across. Cut four 10 mm stainless tubes about 250 mm long, deburr them, and push each into its cross socket and up into the collar. Check that every funnel mouth points the same way round: they must trail as the shaft turns.
Materiais para este passo:
Varão de aço inoxidável1 peça
Tubo de aço inoxidável1 peça
Parafusos de máquina2 peças
Porca de segurança com anel de nylon2 peçasFerramentas necessárias:
Serra de arco para metais
Corta-tubos
Limas (lima de mão)
Conjunto de chaves de fendas11
11
Uprights, wheel E and crank S
Uprights, wheel E and crank S
Stand shaft G in its socket, put the top on and fix the pinion on G's top. Screw two hardwood uprights C 44 x 30 x 158 mm to the top, either side of the wheel's place, bored 12.5 mm at 128 mm up. Run a 12 mm stainless rod through them and the wheel's hub as shaft B so the wheel's teeth mesh with the pinion, fix the wheel with an M4 screw, and fix a hardwood crank S 132 mm long with a dowel handle on B's end.
Materiais para este passo:
Tábua de madeira de lei1 peça
Parafusos para madeira4 peças
Varão de aço inoxidável1 peça
Parafusos de máquina2 peças
Porca de segurança com anel de nylon2 peças
Cavilhas de madeira dura1 peça
Cola de madeira1 peçaFerramentas necessárias:
Serrote
Berbequim sem fios
Jogo de brocas
Serra de arco para metais
Conjunto de chaves de fendas12
12
The build in 3D
The build in 3D
FreeCAD model of this build, the near quarter of the container and top cut away: the shaft on its socket with the cross, funnels, slanting tubes and collar, the meshed top with its uprights, wheel E and pinion F, and the crank.
13
13
Churn
Churn
Pour in about 10 litres of heavy cream at about 15 °C, checked with the thermometer, and put the top on. Turn the crank fast the way that makes the funnels trail, and time it; watch through the gauze for bubbles rising. When the butter comes it gathers between the tubes at the bottom. Lift out the top and shaft, pour off the buttermilk, wash the butter in cold water until it runs clear, work in a pinch of salt and weigh it.
Materiais para este passo:
Natas para bater10 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável14
14
Troubleshooting
Troubleshooting
Atmospheric churn troubleshooting.
Flow
Loading...
15
15
History and honest limits
History and honest limits
**Loren J. Wicks** of Racine, Wisconsin, US 23,208, 8 March 1859, "Churn". He held that the tubes' feet, moving much faster than their tops, upset the balance and draw air in quickly, and that the butter, heavier than the cream, settles between the tubes. He claimed the shaft, slanting tubes, cross pieces and funnels in a square churn with a ventilating top. He gave no sizes or materials, and drew F as a bevel wheel; our pinion is straight-cut, and every size and material is ours.
Materiais
15- Referência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 12 peçasReferência
- 5 peçasReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 1 peçaReferência
- 10 lReferência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
15- Referência
- 1 vendor sell this, none ship to you yetReferência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
6Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Ice-Chamber Air Churn: The Hollow Dasher Pumps the Same Air Round Through Ice and Cream
por Buttercup
COMIDA E BEBIDAS
6
0
0
0
0
0

Segment-Rack Zone Churn: A Lever Rocks the Dasher Shaft, a Toothed Tin Band Gathers the Butter at the Surface
por Buttercup
COMIDA E BEBIDAS
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

