Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL
Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket
Buttercup

Criado por

Buttercup

11. novembro 2026IE
7
0
0
0
0

Rotary-Tub Spout Churn: A Friction Wheel Spins the Tub, a Fixed Spout Catches the Climbing Cream and Jets It Into a Basket

Clark Wright and William Phelps of Sycamore, Illinois, received US 28,802, dated 19 June 1860, for a churn. The tub itself spins, carried on a plate that rests on a crank-turned friction wheel. The cream climbs the side until a flange stops it, where a fixed spout catches it and shoots it into a perforated basket hung loose in the middle; the butter collects in the basket while the milk runs out through its holes and climbs again. The patent gives no sizes; every size here is ours.
Avançado
About 2 days, plus printing

Instruções

1

How fast the tub must turn for the cream to climb

A carregar o notebook Jupyter…
2

Cream flung outward and jetted, three months before

Sangster spins paddles to fling the cream. Wright and Phelps spin the whole tub.
3

Read US 28,802

"A quantity of cream being placed in the tub F, and the latter rapidly rotated by means of the crank D and friction wheel E, the cream ascends the sides of the tub by centrifugal force until arrested by the flange f and being caught by the spout K is deflected inward and projected in a forcible and continuous stream into the basket H, causing violent agitation in the body of cream as well as friction as it flows out through the apertures in the basket."
4

Print the basket H

Perforated cone basket 160 mm across at the top, 130 at the bottom, 150 tall, with a hub bored 12.6 mm. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
5

Print the spout K

Curved spout 40 mm wide, its mouth at the wall turning inward over 55 mm, with a hanger and a clamp that slides along the bar I. PETG, 0.2 mm layers, 30 % infill, 4 walls.
Arquivo de designSTLCC0 - Free
6

Base A, standard B, spindle G and plate g

Make a hardwood base 520 x 560 mm. Screw a hardwood standard 60 mm square in its middle, its top bored 16.6 mm to take a 16 mm stainless spindle. Cut a plywood disk plate 300 mm across, fix the spindle in its centre, and screw the bucket down on it, sealing the screw heads inside with silicone. Screw a ring of HDPE sheet, 26 mm wide, inside the bucket 340 mm up as the flange f, and a hardwood socket bored 12.6 mm in the floor's centre.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei2 peças
Placa de contraplacadoPlaca de contraplacado1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Balde de 20 litrosBalde de 20 litros1 peça
Chapa de PEADChapa de PEAD1 peça
Bloco de madeira duraBloco de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafusos para madeiraParafusos para madeira16 peças
Vedante de siliconeVedante de silicone1 peça

Ferramentas necessárias:

Serra de mesaSerra de mesa
Serra tico-ticoSerra tico-tico
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Conjunto de brocas de páConjunto de brocas de pá
Sargento de barraSargento de barra
Conjunto de chaves de fendasConjunto de chaves de fendas
7

Friction wheel E, shaft C and crank D

Turn a hardwood wheel E 220 mm across with its rim rounded in section, as the patent's "regular convexity". Bolt two hardwood bearing blocks to the base so a 16 mm stainless shaft C runs straight out from under the spindle, at a height where the wheel, fixed on its inner end 50 mm from the spindle, just carries the plate. The shaft must point at the spindle, so the wheel rolls on the plate without scrubbing. Fix the wheel on the shaft, and a hardwood crank D with a dowel handle on its end; hold it with collars.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Cavilhas de madeira duraCavilhas de madeira dura1 peça
Cola de madeiraCola de madeira1 peça
Parafuso de carroçariaParafuso de carroçaria4 peças
Porca borboletaPorca borboleta4 peças
Shaft CollarShaft Collar2 peças

Ferramentas necessárias:

Torno de madeiraTorno de madeira
LixaLixa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Chave inglesa ajustávelChave inglesa ajustável
8

Standards J, bar I, pin, basket H and spout K

Stand two hardwood standards J 30 x 30 mm either side of the bucket and join their tops with a bar I across it, bored 12.6 mm over the centre. Drop a 12 mm stainless pin through the bar into the floor socket and slide the basket onto it so it turns freely. Clip the spout's clamp on the bar so its mouth sits just under the flange, close to the wall, facing against the tub's turn; slide it in or out to suit.

Materiais para este passo:

Tábua de madeira de leiTábua de madeira de lei1 peça
Varão de aço inoxidávelVarão de aço inoxidável1 peça
Parafusos para madeiraParafusos para madeira6 peças
Cola de madeiraCola de madeira1 peça
Filamento PETGFilamento PETG1 peça

Ferramentas necessárias:

Impressora 3D de filamento (FDM)Impressora 3D de filamento (FDM)
Serra de mesaSerra de mesa
Berbequim sem fiosBerbequim sem fios
Jogo de brocasJogo de brocas
Serra de arco para metaisSerra de arco para metais
Fita métricaFita métrica
9

The build in 3D

FreeCAD model of this build, the tub cut open: the spindle and plate on the friction wheel and crank, the flange, the basket on its pin, the spout hanging from the bar, and the standards.
Arquivo de designBLENDCC0 - Free
10

Churn

Pour about 5 litres of heavy cream at about 15 °C, checked with the thermometer, into the tub around the basket. Turn the crank briskly, timing it, until the cream climbs to the flange and runs from the spout into the basket. Keep on until the butter has gathered in the basket. Lift out the pin and basket with the butter, pour off the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.

Materiais para este passo:

Natas para baterNatas para bater5 l
Sal marinho grossoSal marinho grosso1 peça
ÁguaÁgua1 peça

Ferramentas necessárias:

Termómetro de sonda permanenteTermómetro de sonda permanente
CronómetroCronómetro
Balança digital de cozinhaBalança digital de cozinha
Taça grande de aço inoxidávelTaça grande de aço inoxidável
11

Troubleshooting

Rotary-tub churn troubleshooting.

Flow

Loading...
12

History and honest limits

**Clark Wright** and **William Phelps** of Sycamore, DeKalb County, Illinois, US 28,802, 19 June 1860, "Churn". They claimed the rotary tub, stationary spout and basket together. Their wheel and plate meet as two crossed discs, the wheel's rounded rim avoiding both side thrust and broad rubbing faces. Every size here is ours.

Materiais

17

Ferramentas necessárias

17

Ficheiros de design

3

CC0 Domínio Público

Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.

Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

Discussão

(0)

Entrar para participar da discussão

Carregando comentários...