Colaboração
ARTE
BELEZA E BEM-ESTAR
ARTESANATO
CULTURA E HISTÓRIA
ENTRETENIMENTO
MEIO AMBIENTE
COMIDA E BEBIDAS
ENGENHARIA REVERSA
CIÊNCIAS
ESPORTES
TECNOLOGIA
TECNOLOGIA VESTÍVEL

False-Bottom Jet Churn: Paddles Under a Pierced Partition Draw Cream Down at the Centre and Jet It Up at the Rim
James Sangster of Buffalo, New York, received US 27,570, dated 20 March 1860, for a churn. A false bottom divides the churn; paddles spinning beneath it draw the cream and air down through holes near its centre and throw it up through holes near its rim, under caps that aim the streams against each other. Another paddle turns above. The cream goes round and round, from rim to centre and back.
The patent gives no sizes; every size here is ours.
Intermediário
About 2 days, plus printing
Instruções
1
1
Down at the centre, up at the rim
Down at the centre, up at the rim
A carregar o notebook Jupyter…
2
2
An upright churn with a pierced cover, one week before
An upright churn with a pierced cover, one week before
Wiswell's cover is above the scoops. Sangster's pierced partition is below the cream, with paddles under it.
3
3
Read US 27,570
Read US 27,570
"U and V represent caps which partially cover the apertures L and N. They are placed in such a position as to cause the fluid to flow in streams against each other, by boring the holes L and N at the same angles at which the caps U and V are set. The caps may be dispensed with and the same result obtained."
4
4
Print the caps Q, U, W, V
Print the caps Q, U, W, V
Hood cap 50 mm across, open on one side. Print four. PETG, 0.2 mm layers, 40 % infill, 4 walls.
5
5
Print the crown wheel
Print the crown wheel
Crown wheel, 36 teeth on its face, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
6
6
Print the pinion
Print the pinion
Spur pinion, 12 teeth, module 2, with a hub; bored 12.4 mm. PETG, 0.2 mm layers, 40 % infill, 4 walls.
7
7
Rim Y and partition E
Rim Y and partition E
Screw a ring of HDPE strip 10 mm thick and 12 high inside the bucket with its top 60 mm above the floor, as the rim Y, sealing the screw holes outside with silicone. Cut a disc of 10 mm HDPE sheet to rest on it, bored 17 mm in the centre. Bore four 30 mm holes, H, I, J, K, 45 mm from the centre, a quarter turn apart, and four 25 mm holes, L, M, N, O, 112 mm from the centre between them, each bored at 45 degrees slanting toward the centre as it rises. Screw a printed cap over each rim hole, its open side toward the centre.
Materiais para este passo:
Balde de 20 litros1 peça
Chapa de PEAD1 peça
Parafusos de máquina16 peçasFerramentas necessárias:
Serra tico-tico
Conjunto de serras-copo
Berbequim sem fios
Jogo de brocas
Transferidor
Limas (lima de mão)
Conjunto de chaves de fendas8
8
Spindle D, paddles C, G and Z, shoulder J'
Spindle D, paddles C, G and Z, shoulder J'
Screw a hardwood block 50 x 50 x 6 mm to the floor's centre and bore it 17 mm, 5 deep, as the step. Cut a 16 mm stainless spindle 435 mm long and turn or file its top 75 mm down to 12 mm. Fix a hardwood paddle bar 250 x 45 x 20 mm across it, 8 mm above the floor when the spindle stands in its step (the paddles C and G), pass it up through the partition, and fit a printed or hardwood collar 32 mm across and 20 high on it just above the partition as the shoulder J'. Fix a second paddle Z, 200 x 30 x 20 mm, across it 185 mm above the floor.
Materiais para este passo:
Varão de aço inoxidável1 peça
Tábua de madeira de lei1 peça
Bloco de madeira dura1 peça
Cola de madeira1 peça
Parafusos para madeira2 peças
Shaft Collar2 peças
Contrapino2 peçasFerramentas necessárias:
Serra de arco para metais
Limas (lima de mão)
Torno de bancada
Berbequim sem fios
Jogo de brocas
Serra de mesa
Lixa
Conjunto de chaves de fendas9
9
Top I' and crank X
Top I' and crank X
Cut a hardwood top 350 x 205 x 25 mm to sit on the bucket's rim and bore it 13 mm over the centre for the spindle; fit the pinion on the spindle above it. Screw two hardwood chairs on the top carrying a 12 mm stainless crank shaft with the crown wheel meshing the pinion, and fit a hardwood crank X with a dowel handle on its end.
Materiais para este passo:
Tábua de madeira de lei2 peças
Varão de aço inoxidável1 peça
Cavilhas de madeira dura1 peça
Cola de madeira1 peça
Parafusos para madeira8 peças
Shaft Collar2 peças
Filamento PETG1 peçaFerramentas necessárias:
Impressora 3D de filamento (FDM)
Serra de mesa
Berbequim sem fios
Jogo de brocas
Conjunto de brocas de pá
Serra de arco para metais
Sargento de barra
Conjunto de chaves de fendas
Fita métrica10
10
The build in 3D
The build in 3D
FreeCAD model of this build, the bucket cut through the middle: the paddles C and G under the partition E on its rim Y, the centre and rim holes with their caps, the shoulder J', the paddle Z, and the top with the crank, crown wheel and pinion.
11
11
Churn
Churn
Pour about 8 litres of heavy cream at about 15 °C, checked with the thermometer, into the bucket over the partition, set the top and gearing on the rim, and turn the crank steadily, timing it. When the butter comes, lift off the top, lift out the spindle and partition, take out the butter, pour the buttermilk into a bowl, wash the butter in cold water until it runs clear, salt and weigh it.
Materiais para este passo:
Natas para bater8 l
Sal marinho grosso1 peça
Água1 peçaFerramentas necessárias:
Termómetro de sonda permanente
Cronómetro
Balança digital de cozinha
Taça grande de aço inoxidável12
12
Troubleshooting
Troubleshooting
False-bottom churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**James Sangster** of Buffalo, New York, US 27,570, 20 March 1860, "Churn". He claimed the paddles Z, C and G with the partition E pierced near its centre and near its rim under caps, "for the purpose of passing the cream around and around through the openings from circumference to center and vice versa". He made it of "wood, tin or any other suitable material"; ours is a food-grade bucket with an HDPE partition and printed caps and gears. Every size here is ours.
Materiais
16- 1 peçaReferência
- 1 peçaReferência
- 16 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- 2 peçasReferência
- 1 peçaReferência
- 2 peçasReferência
- 10 peçasReferência
- 2 peçasReferência
- 2 peçasReferência
- 1 peçaReferência
- 1 peçaReferência
- Referência
- 1 peçaReferência
- 1 peçaReferência
Ferramentas necessárias
19- 1 vendor sell this, none ship to you yetReferência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
- 1 vendor sell this, none ship to you yetReferência
- Referência
- Referência
- Referência
- Referência
Ficheiros de design
4Blueprints relacionados
Estes blueprints compartilham conhecimento — técnicas, materiais ou princípios

Leaning-Scoop Churn: Three Scoops Tilted 10, 5 and 0 Degrees Throw the Cream at Sharp-Topped Ribs and a Slit Cover
por Buttercup
Marcenaria
6
0
0
0
0
0

Counter-Revolving Dasher Churn: Geared Dashers on Offset Shafts Turn Contrary Ways, Their Blades Skewed Contrary Ways
por Buttercup
Marcenaria
6
0
0
0
0
0

Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANATO
63
0
0
0
0
0
CC0 Domínio Público
Este blueprint é liberado sob CC0. Você é livre para copiar, modificar, distribuir e usar este trabalho para qualquer finalidade, sem pedir permissão.
Apoie o Maker comprando produtos através do Blueprint, onde ele ganha uma Comissão Maker definida pelos vendedores, ou crie uma nova versão deste Blueprint e inclua-o como conexão no seu próprio Blueprint para compartilhar receita.

