艺术
美容与健康
工艺
文化与历史
娱乐
环境
食品与饮料
逆向工程
科学
体育
技术
可穿戴设备

Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
The Hights made the wings of a horizontal box-churn dash into a screw.
Cornelius R. Hight and John Hight of Geneva, Illinois, received US 7,490, dated 9 July 1850, for a "reacting spiral revolving dash" in a box churn: a shaft with four arms, those at one end at right angles to those at the other, and two wings fastened from arm to arm "so as to produce a quarter twist in the wings as they extend along the shaft." Its revolution produces "opposite currents, in the cream"; reversed, "the butter collects at the ends of the wings."
This rung works out the wings' pitch, then prints the dash in one piece, fits it in a box, and makes butter.
中级
About 3 hours, plus printing
说明
1
1
The quarter twist
The quarter twist
正在加载 Jupyter 笔记本…
2
2
Oblique wings on a horizontal arbor before it
Oblique wings on a horizontal arbor before it
The embedded blueprint sets straight wings at 30° to the axle. The Hights twist theirs a quarter turn from end to end, like a screw.
3
3
Read US 7,490
Read US 7,490
"The peculiar construction of the dash, consists in setting the arms to which the wings are attached, at right angles, upon opposite sides of the shaft, so as to produce a quarter twist in the wings as they extend along the shaft from one arm to the other."
4
4
Print the dash
Print the dash
Print the dash on end in one piece with supports (/uploads/blueprints/quarter-twist-spiral-dash-churn-dash.stl): shaft, four arms and two wings each twisted a quarter turn. Print the crank arm (/uploads/blueprints/quarter-twist-spiral-dash-churn-crank-arm.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
此步骤所需材料:
PETG线材1 个所需工具:
FDM 3D 打印机5
5
Fit the box
Fit the box
Take a food-safe box about 220 × 150 × 160 mm, its proportions close to his 18 × 12 × 13 inches. Drill both ends on the axis 80 mm up. Push a 10 mm square hardwood shaft through one end, the dash and the other end, with a leather washer at each.
此步骤所需材料:
食品级贮存容器1 个
硬木销钉1 个
皮条1 个所需工具:
充电式电钻
钻头套装
手锯6
6
Crank and lid
Crank and lid
Glue the crank arm and a dowel handle on the shaft's outer end, and fit the box's lid, as his rabbeted cover.
此步骤所需材料:
硬木销钉1 个
木工胶1 个所需工具:
砂纸7
7
The patent drawing
The patent drawing
US 7,490 drawing sheet, public domain (expired patent).

8
8
Churn, then reverse to collect
Churn, then reverse to collect
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Crank steadily; time until the butter comes. Then reverse the crank so the butter collects at the ends of the wings, as they said. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
此步骤所需材料:
鲜奶油1500 毫升
粗海盐1 个
水1 个所需工具:
留置式探针温度计
秒表
数字厨房秤
大号不锈钢搅拌盆9
9
Wings that scrape, butter that won't collect
Wings that scrape, butter that won't collect
Quarter-twist spiral dash troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Cornelius R. Hight and John Hight** of Geneva, Kane County, Illinois, received US 7,490, dated 9 July 1850. Their wings could be wood or tin, split into the arms with a saw and fastened with brads or small screws; the wing's inner border was cut to arcs of 16- and 23-inch circles; the dash ran on a coupling gudgeon in a cast box and a screw pivot. They wrote it made butter "in from 5 to 8 minutes"; that is their claim, not our measurement. They claimed the application of a reacting spiral revolving dash to a box churn or any of the usual forms of churns.
**Honest limits.** A food-safe box and a printed dash stand in for theirs, and our wings twist evenly rather than following their curved borders. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
材料
8- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1 个占位符
- 1500 毫升占位符
- 1 个占位符
- 1 个占位符
此蓝图制作
相关蓝图
这些蓝图共享知识——技术、材料或原理
CC0 公共领域
此蓝图以 CC0 协议发布。你可以自由复制、修改、分发和使用此作品,无需征得许可。
通过购买蓝图中的产品支持创客,他们将获得 创客佣金 (由供应商设定),或创建此蓝图的新版本并将其作为连接包含在你自己的蓝图中以分享收入。



