KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Cone-Wing Counter-Current Churn: Wings That Spin on Their Own Axles Break the Whirl
Lewis P. Pease of Mount Carmel, Illinois, received US 13,686, dated 16 October 1855, for two winged cones of curved paddles on axles projecting "outward and slightly upward" from the foot of the shaft. The cream turns them on their axles, and the counter currents break up the main vortex.
This rung prints the wings, hub, step and gears, builds the churn and makes butter.
Fortgeschritten
About 4 hours, plus printing
Anweisungen
1
1
The wing's tilt
The wing's tilt
Jupyter-Notebook wird geladen …
2
2
Stopping the whirl before it
Stopping the whirl before it
Wade stops the cream turning with slats and brakes; Pease with wings that spin.
3
3
Read US 13,686
Read US 13,686
"This rotation of each wing around its respective axle, results in a constant breaking up of the principal vortex by the counter currents thus generated by the wings, and hence there results a more violent agitation of the cream, and consequently a more speedy formation of butter."
4
4
Print the parts
Print the parts
Print two cone wings, the wing hub, the step, the crown wheel, the pinion and the standard. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materialien für diesen Schritt:
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-Drucker5
5
Print the cone wing
Print the cone wing
The cone wing, printed as step 4 describes.
6
6
Print the wing hub
Print the wing hub
The wing hub, printed as step 4 describes.
7
7
Print the step
8
8
Print the crown wheel
Print the crown wheel
The crown wheel, printed as step 4 describes.
9
9
Print the pinion
Print the pinion
The pinion, printed as step 4 describes.
10
10
Print the standard
Print the standard
The standard, printed as step 4 describes.
11
11
Wings and shaft
Wings and shaft
Push two 6 mm stainless rods into the hub's slanting holes and glue them. Slide a wing onto each, big head outward, with a washer and nut at the end so it spins freely. Push the hub onto a 10 mm square hardwood shaft standing in the step, in a square food-grade container about 210 mm across.
Materialien für diesen Schritt:
Rundstahl (Baustahl)1 Stück
Unterlegscheibe1 Stück
Sechskantmutter1 Stück
Zweikomponentenepoxid1 Stück
Hartholzdübel1 Stück
Vorratsbehälter in Lebensmittelqualität1 StückBenötigte Werkzeuge:
Bügelsäge (Metallsäge)
Rollgabelschlüssel12
12
Lid, gears and crank
Lid, gears and crank
Fix half the lid with a hole for the shaft, the pinion on the shaft's top and the standard with the crown wheel meshing it; screw a dowel handle into the wheel.
Materialien für diesen Schritt:
Rundstahl (Baustahl)1 StückHartholzdübel1 Stück
Holzschraube #8 x 1"1 Stück
Maschinenschrauben1 StückBenötigte Werkzeuge:
Schraubendreher-Satz
Akkubohrschrauber13
13
The build in 3D
The build in 3D
FreeCAD model of this build: the tub cut away to show the two cone wings on their rising axles at the shaft's foot, and the crown wheel and pinion above.
14
14
Churn
Churn
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Crank steadily and check the wings spin on their axles; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materialien für diesen Schritt:
Schlagsahne2000 ml
Grobes Meersalz1 Stück
Wasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus Edelstahl15
15
Troubleshooting
Troubleshooting
Cone-wing churn troubleshooting.
Flow
Loading...
16
16
History and honest limits
History and honest limits
**Lewis P. Pease** of Mount Carmel, Wabash County, Illinois, US 13,686, 16 October 1855. He claimed the winged dasher of two series of curved paddles, each a conic frustum turning on an axle rising from the shaft, its lower edge parallel to the tub's bottom. He did not describe the drive; a crown wheel and pinion stand in. FDM prints hold food in their layer lines, so wash well and replace when worn.
Materialien
12- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- Platzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 2000 mlPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
9- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
7Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Braked-Disk Slat-and-Wing Churn: Up Between the Slats, Down Through the Disk
von Martin
ESSEN & GETRÄNKE
30
0
0
0
0
0
Adjustable-Pin Resistance Churn: Flat-Ended Pins Turned From Outside Set the Churn's Grip
von Martin
ESSEN & GETRÄNKE
37
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
von TheChef
HANDWERK
54
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.