KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
GRÜNE ZUKUNFT
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Forging an Iron Strap Hinge — The Joint That Opens Every Door
Forge

Erstellt von

Forge

26. Mai 2026NO
11
0
0
0
0

Forging an Iron Strap Hinge — The Joint That Opens Every Door

Before the iron hinge, doors were hung on leather straps or wooden pivots that wore out in months. The iron strap hinge — two flat straps joined by a pin through rolled eyes — solved this problem permanently. A well-made iron hinge lasts centuries, as demonstrated by medieval church doors still swinging on their original hinges after 800 years.

A strap hinge is forged from two flat iron bars. Each bar has one end curled into a tube (the eye) around a mandrel. A pin passes through both eyes to create the pivot. One strap is nailed to the door and the other to the frame. The hinge works because the eyes wrap around the pin with just enough clearance to rotate freely but not wobble.

This blueprint teaches three essential smithing operations: drawing flat bar, scrolling (curling metal around a mandrel), and punching nail holes. These same operations appear in gates, latches, brackets, and every other piece of architectural ironwork.

Fortgeschritten
2-3 hours (one pair of hinges)

Anweisungen

1

Cut the strap blanks

Cut two pieces of wrought iron flat bar. The door strap (the long leaf) should be about 30 cm long, 4 cm wide, and 5 mm thick. The frame strap (the short leaf) should be about 15 cm long with the same width and thickness. These dimensions suit a medium door — scale up for heavy gates, down for cabinet doors.
2

Forge the eye on the door strap

Heat the last 5-6 cm of the long strap to bright orange. Place a round mandrel (an iron rod about 10-12 mm diameter) against the end of the strap on the anvil edge. Hammer the hot end down and around the mandrel, curling the iron into a complete tube. The eye must wrap at least 270 degrees — ideally a full 360. Remove the mandrel and check that it slides freely back through the eye. If the eye is too tight, reheat and open slightly with the mandrel.

Materialien für diesen Schritt:

CharcoalCharcoal3 kg

Benötigte Werkzeuge:

Forge Hammer (Cross-Peen)Forge Hammer (Cross-Peen)
Forge TongsForge Tongs
Hearth (Forge Fire)Hearth (Forge Fire)
3

Forge the eye on the frame strap

Repeat the same curling operation on the short strap. The two eyes must be the same diameter so they align on a common pin. Place both eyes side by side and check that the mandrel passes through both smoothly. If one eye is tighter or offset, reheat and adjust.
4

Punch the nail holes

Each strap needs holes for the nails or screws that attach it to the wood. Heat a section of the strap to bright orange and drive a square punch through from one side, using the pritchel hole in the anvil to clear the slug. Space the holes evenly along the strap — three to four holes per leaf for a medium hinge. The holes should be sized to accept the hand-forged nails from your nail-making stock.
5

Decorative taper (optional)

Traditional strap hinges often have a decorative taper or point at the free end of the door strap. Heat the end and draw it to a gentle taper, or split it with a hot chisel and curl the two halves into scrolls. This serves no structural purpose but identifies the smith's work and adds beauty to the door. Many surviving medieval hinges have elaborate scroll terminals.
6

Make the hinge pin

Forge a pin from round rod stock, sized to fit snugly through both eyes. The pin should be about 2-3 cm longer than the combined width of both eyes. After inserting the pin, peen over the top end to form a small head that prevents the pin from dropping out. Leave the bottom end straight or bend it into a small hook for easy removal — a removable pin allows the door to be taken off its hinges.
7

Assemble and test the hinge

Thread the pin through both eyes — the door strap eye and the frame strap eye should interlock, with the straps extending in opposite directions. Swing the hinge open and closed to check that it pivots freely through at least 180 degrees. If it binds, the eyes are misaligned — reheat the offending eye and adjust. Apply a thin coat of tallow or grease to the pin to prevent rust and reduce friction.

Materialien

1

Benötigte Werkzeuge

3

Materialien verbundener Blueprints

Verwandte Blueprints

Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien

Forging an Iron Knife from a Wrought Iron Bar — The Smith's First Projectvon Forge
Forge Welding Iron — Joining Two Pieces into Onevon Forge

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...