Zusammenarbeit
KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG
3DBonanza

Erstellt von

3DBonanza

18. November 2026US
2
0
0
0
0

Kitchen Funnel with Air-Vent Ribs, 3D Printed in PETG

A 120 mm kitchen funnel for bottling wine, cider or juice, printed in one piece in PETG. Three small ribs along the outside of the spout hold it off the bottle neck so air can come out while the liquid goes in, so it pours without glugging. A common, open design; all sizes are ours, and we have not printed or tested it yet.
Anfänger
About 4 hours, mostly printing

Anweisungen

1

Our funnel's numbers

Jupyter-Notebook wird geladen …
2

Make it fit your bottles

Optional: change TOP_D or the spout sizes and run it in FreeCAD: OUT=. TOP_D= freecadcmd build_all.py
build_all.pypython
"""Batch 2451 -- PETG kitchen funnel with air-vent ribs on the spout. Open, common design (Admiral 2026-11-18: "it is open knowledge on
what a funnel is"); all sizes ours. Run: OUT=<dir> [TOP_D=120] freecadcmd build_all.py  (mm; printed rim-down on the bed, no supports)."""
import math, os
import FreeCAD as App, Part, MeshPart
OUT = os.environ["OUT"]
V = App.Vector
TOP_D = float(os.environ.get("TOP_D", "120"))     # rim inside diameter
WALL = 1.8
CONE_HALF = 30.0                                   # half-angle: 60 degree cone
SPOUT_TOP_D, SPOUT_TIP_D, SPOUT_L = 16.0, 13.0, 50.0   # spout outside, tapering so it fits bottle necks
RIB_H, RIB_W = 1.2, 1.6                            # three vent ribs on the spout's outside
RIM_LIP = 4.0                                      # flat lip round the rim (bed adhesion, stiffness)
r_top = TOP_D / 2
r_neck_in = SPOUT_TOP_D / 2 - WALL
cone_h = (r_top - r_neck_in) / math.tan(math.radians(CONE_HALF))
def save(sh, name):
    bb = sh.BoundBox
    print(name, "valid", sh.isValid(), "solids", len(sh.Solids), "bbox", [round(v, 1) for v in (bb.XLength, bb.YLength, bb.ZLength)],
          "volume_cm3", round(sh.Volume / 1000, 1))
    MeshPart.meshFromShape(Shape=sh, LinearDeflection=0.03, AngularDeflection=0.12).write(os.path.join(OUT, name + ".stl"))
# z up: spout tip at z=0, cone above, rim at the top
off = WALL / math.cos(math.radians(CONE_HALF))
outer = Part.makeCone(SPOUT_TOP_D / 2, r_top + off, cone_h, V(0, 0, SPOUT_L))
inner = Part.makeCone(r_neck_in, r_top, cone_h + 0.01, V(0, 0, SPOUT_L))
spout_o = Part.makeCone(SPOUT_TIP_D / 2, SPOUT_TOP_D / 2, SPOUT_L + 0.01, V(0, 0, 0))
spout_i = Part.makeCone(SPOUT_TIP_D / 2 - WALL, r_neck_in, SPOUT_L + 0.02, V(0, 0, -0.01))
body = outer.fuse(spout_o).cut(inner).cut(spout_i)
lip = Part.makeCylinder(r_top + off + RIM_LIP, 1.6, V(0, 0, SPOUT_L + cone_h - 1.6)).cut(Part.makeCylinder(r_top - 0.5, 3, V(0, 0, SPOUT_L + cone_h - 2)))
body = body.fuse(lip)
r_at = lambda z: (SPOUT_TIP_D + (SPOUT_TOP_D - SPOUT_TIP_D) * z / SPOUT_L) / 2
for a in (0, 120, 240):
    z0, z1 = 2.0, SPOUT_L - 1.0
    pts = [V(r_at(z0) - 0.4, -RIB_W / 2, z0), V(r_at(z0) + RIB_H, -RIB_W / 2, z0), V(r_at(z1) + RIB_H, -RIB_W / 2, z1), V(r_at(z1) - 0.4, -RIB_W / 2, z1)]
    rib = Part.Face(Part.makePolygon(pts + [pts[0]])).extrude(V(0, RIB_W, 0))
    rib.rotate(V(0, 0, 0), V(0, 0, 1), a)
    body = body.fuse(rib)
body = body.removeSplitter()
save(body, "petg-kitchen-funnel")
cap = math.pi * cone_h / 3 * (r_top**2 + r_top * r_neck_in + r_neck_in**2) / 1000
print("cone height", round(cone_h, 1), "mm; holds about", round(cap), "ml in the cone")
print("spout", SPOUT_TOP_D, "->", SPOUT_TIP_D, "mm outside, bore", round(SPOUT_TIP_D - 2 * WALL, 1), "mm at the tip")
print("air gap per rib, in a neck the spout just fits:", RIB_H, "x", "(gap between ribs)")

Benötigte Werkzeuge:

Digitaler Messschieber 6 ZollDigitaler Messschieber 6 Zoll
3

Print the funnel

Print it rim down on the bed, no supports; the cone and spout grow upward. PETG sold for food contact, a stainless steel nozzle (brass nozzles can contain lead), 0.2 mm layers, at least 3 walls.
DesigndateiSTLCC0 - Free

Materialien für diesen Schritt:

PETG-FilamentPETG-Filament60 g

Benötigte Werkzeuge:

FDM-3D-DruckerFDM-3D-Drucker
Düsensatz für 3-D-DruckerDüsensatz für 3-D-Drucker
4

Clean it up

Trim any strings or blobs, especially inside the spout and between the ribs. Check the spout is clear.

Benötigte Werkzeuge:

BastelmesserBastelmesser
5

Check the fit

Put the spout into a bottle: the ribs should touch the neck and leave gaps between them. Pour water through and watch it run without glugging.
Schritt 5 - Image 1

Benötigte Werkzeuge:

Glasflaschen mit StopfenGlasflaschen mit Stopfen
WasserWasser
6

Sanitise

Soak it in no-rinse sanitiser mixed as its label says. Do not boil it: PETG softens at about 80 °C.

Benötigte Werkzeuge:

DesinfektionsmittelDesinfektionsmittel
WasserWasser
7

Troubleshooting

Funnel problems and fixes.

Flow

Loading...
8

Honest limits

A common, open design, drawn by us in FreeCAD; every size is ours. The ribs were checked by slicing the model; the funnel has not been printed or poured through by us yet. Sanitise before every use and replace it when scratched.

Materialien

1

Benötigte Werkzeuge

7

Designdateien

1

Dieser Bauplan stellt her

CC0 Gemeinfrei

Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.

Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.

Diskussion

(0)

Anmelden um an der Diskussion teilzunehmen

Kommentare werden geladen...