KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Propeller-and-Spoon Egg Beater: Spoon Arms Break the Swirl
A turning beater soon sets the whole liquid circling with it.
William T. Nicholson of Providence, Rhode Island, received US 32,886, dated 23 July 1861, for an egg beater: a crank wheel with bevelled face teeth turns a pinion and a pair of propeller blades; under the pinion a disk with an elliptic groove rocks two arms ending "in the form of a spoon bill's beak," so "the circling currents occasioned by the blades of the propeller will be broken at regular intervals." It clamps into a socket on a table or lifts out for use by hand.
This rung works out the stroke rates, then prints the crown wheel, pinion, cam and propeller, builds the frame and arms, and times a beating.
Erfahren
About 5 hours, plus printing
Anweisungen
1
1
Stroke rates
Stroke rates
Jupyter-Notebook wird geladen …
2
2
A crank wheel and pinion before it
A crank wheel and pinion before it
The embedded blueprint drives two beaters off one wheel. Nicholson drives a propeller and lets a cam rock two spoon arms against its swirl.
3
3
Read US 32,886
Read US 32,886
"To the under side of the pinion E is secured the disk H (Fig. 5,) its lower surface being furnished with an elliptic groove or channel I. Two arms K K pivoted to the handle at c and d extend to the bottom of the propeller blade their lower extremities being in the form of a spoon bill's beak. A projecting ear e, e on each arm is inserted in the elliptic groove I whereby as the propeller shaft F is rotated to which the disk is attached a reciprocating motion is given to each of the arms."
4
4
Print the gears, cam and propeller
Print the gears, cam and propeller
Print the 48-tooth crown wheel, the 12-tooth pinion, the cam disk with its elliptic groove and the propeller. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls.
Materialien für diesen Schritt:
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-Drucker5
5
Print the crown wheel
Print the crown wheel
The crown wheel, printed as step 4 describes.
6
6
Print the pinion
Print the pinion
The pinion, printed as step 4 describes.
7
7
Print the cam
8
8
Print the propeller
Print the propeller
The propeller, printed as step 4 describes.
9
9
Frame and wheel
Frame and wheel
Cut a plywood handle frame. Bolt the crown wheel to it on an M5 screw with a crank near its rim, and drill a bearing for the propeller shaft so the pinion meshes the wheel's face.
Materialien für diesen Schritt:
Sperrholzplatte1 Stück
Maschinenschrauben1 Stück
Unterlegscheibe1 Stück
Sechskantmutter1 StückBenötigte Werkzeuge:
Laubsäge (Schweifsäge)
Akkubohrschrauber
Bohrersatz
Rollgabelschlüssel10
10
Shaft, cam and propeller
Shaft, cam and propeller
Epoxy the pinion, then the cam under it, on a 5 mm rod through the bearing, and the propeller on the rod's foot.
Materialien für diesen Schritt:
Rundstahl (Baustahl)1 Stück
Zweikomponentenepoxid1 StückBenötigte Werkzeuge:
Bügelsäge (Metallsäge)
Schraubstock11
11
Spoon arms
Spoon arms
Bend two arms of stainless wire with a spoon-shaped flat at the foot. Pivot each on a screw in the frame either side of the shaft, and bend a short ear on each into the cam's groove.
Materialien für diesen Schritt:
Edelstahldraht1 Stück
Holzschraube #8 x 1"1 StückBenötigte Werkzeuge:
Rundzange
Flachzange
Schraubendreher-Satz
Digitaler Messschieber 6 Zoll12
12
The patent drawing
The patent drawing
US 32,886 drawing sheet, public domain (expired patent).
13
13
With and without the arms
With and without the arms
Beat two egg whites with the arms in the groove and time them to stiff peaks; lift the ears out and repeat with the propeller alone.
Materialien für diesen Schritt:
Ei4 StückBenötigte Werkzeuge:
Große Rührschüssel aus Edelstahl
Stoppuhr14
14
Arms that jam, a cam that throws them
Arms that jam, a cam that throws them
Propeller-and-spoon egg beater troubleshooting.
Flow
Loading...
15
15
History and honest limits
History and honest limits
**William T. Nicholson** of Providence, Rhode Island, received US 32,886, dated 23 July 1861. The grooved disk is set with its longest diameter in the same plane as the propeller blades, so the arms clear the blades; the socket or chair fixes to a table by spurs and one wood screw, its inclined sides grasping the handle, which can be lifted out for use by hand. He claimed the reciprocating beaters combined with a revolving beater.
**Honest limits.** FDM prints hold food in their layer lines, so wash well and replace when worn. A crown wheel and spur pinion stand in for his bevelled wheel, and a plywood frame for his handle and socket. Your times are the result.
Materialien
10- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 4 StückPlatzhalter
Benötigte Werkzeuge
13- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
4Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.