KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
S-Dasher Friction-Board Churn: A Double-Curved Dasher Throwing Cream Over Grooved Boards
The Walkers lined a square churn with grooved boards so the cream would be thrown against them "thus keeping up a constant friction on all sides."
William Walker and Matthew C. Walker of Lancaster, Pennsylvania, received US 7,554, dated 6 August 1850, for a square water-tight box about fourteen inches each way holding about 40 quarts, half filled, with a "double curved or S shaped dasher" revolving in the centre by a crank and a thumb screw. Four grooved cross pieces run along each side of its curved ends; a friction board grooved underneath inclines across the top; a triangular board returns the cream onto it; a grooved friction piece sits in the lower right corner.
This rung checks the box's capacity, then prints the S dasher, friction boards and corner piece, fits them in a box, and makes butter.
Fortgeschritten
About 4 hours, plus printing
Anweisungen
1
1
Capacity
Capacity
Jupyter-Notebook wird geladen …
2
2
A shaped dash in a box churn before it
A shaped dash in a box churn before it
The embedded blueprint twists its wings into a screw. The Walkers bend theirs into an S and add grooved boards round the box for friction.
3
3
Read US 7,554
Read US 7,554
"As the churn is put in operation, the cream is thrown against the grooves of the incline board E, dashed around and under it, and passed over and against the friction piece G, in the right hand corner of box, while the ends of the dasher H and wide cross piece N keep the cream continually dashing against the grooves of the incline board E thus keeping up a constant friction on all sides."
4
4
Print the parts
Print the parts
Print the S dasher with its four grooved cross pieces in one piece, the grooved incline board, the grooved corner piece and the crank arm. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materialien für diesen Schritt:
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-Drucker5
5
Print the S dasher
Print the S dasher
The S dasher, printed as step 4 describes.
6
6
Print the incline board
Print the incline board
The incline board, printed as step 4 describes.
7
7
Print the corner piece
Print the corner piece
The corner piece, printed as step 4 describes.
8
8
Print the crank arm
Print the crank arm
The crank arm, printed as step 4 describes.
9
9
Fit the box
Fit the box
Take a food-safe box about 180 mm each way. Glue the incline board across the top, sloping down to within 20 mm of the left side, grooves underneath, and a triangular plywood board on that side to turn the cream back onto it. Glue the corner piece in the lower right corner. Drill both ends on the centre for the dasher's shaft.
Materialien für diesen Schritt:
Vorratsbehälter in Lebensmittelqualität1 Stück
Sperrholzplatte1 Stück
Silikondichtmasse1 StückBenötigte Werkzeuge:
Laubsäge (Schweifsäge)
Akkubohrschrauber
Bohrersatz
Schraubzwingen10
10
Dasher and crank
Dasher and crank
Pass a 10 mm square hardwood shaft through the box and the dasher, glue the crank arm and a dowel handle on one end, and hold the other with a thumb screw through a washer, as theirs. Cut an air hole in the lid.
Materialien für diesen Schritt:
Hartholzdübel1 Stück
Maschinenschrauben1 Stück
Unterlegscheibe1 Stück
Holzleim1 StückBenötigte Werkzeuge:
HandsägeAkkubohrschrauber
Schraubendreher-Satz11
11
The patent drawing
The patent drawing
US 7,554 drawing sheet, public domain (expired patent).
12
12
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Fill the box half full, about 2.9 litres. Crank steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materialien für diesen Schritt:
Schlagsahne2900 ml
Grobes Meersalz1 Stück
Wasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus Edelstahl13
13
Dasher that strikes, cream that escapes
Dasher that strikes, cream that escapes
S-dasher friction-board troubleshooting.
Flow
Loading...
14
14
History and honest limits
History and honest limits
**William Walker and Matthew C. Walker** of Lancaster, Pennsylvania, received US 7,554, dated 6 August 1850. Their box was of inch boards; a ledge at the top confined the lid, with a projecting strip on its underside to close it tight, and an aperture M let the air through. They claimed the double-curved S-shaped dasher with the grooved pieces.
**Honest limits.** A food-safe box and printed parts stand in for their wooden churn, at about a third of its size. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Materialien
11- 1 StückPlatzhalter
- Platzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 2900 mlPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
11- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
4Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Quarter-Twist Spiral Dash Churn: Wings Twisted Between Arms Set at Right Angles
von Woody
Holzbearbeitung
17
0
0
0
0
0
Butter-Strainer Churn: Cream Thrown Into a Strainer That Keeps the Butter
von TheChef
ESSEN & GETRÄNKE
41
0
0
0
0
0
Shaftless Dasher-Wheel Churn: Bevelled Buckets Drive the Cream to the Centre
von Martin
ESSEN & GETRÄNKE
39
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.