KUNST
SCHÖNHEIT & WELLNESS
HANDWERK
KULTUR & GESCHICHTE
UNTERHALTUNG
UMFELD
ESSEN & GETRÄNKE
REVERSE ENGINEERING
WISSENSCHAFTEN
SPORT
TECHNOLOGIE
WEARABLES
Whirl-Frame Air Dasher Churn: Free Wheels Spun by the Milk Inside a Revolving Frame
Routzahn put free-turning wheels inside his dasher so the milk itself would spin them.
Nathaniel Routzahn of Middletown, Maryland, received US 7,199, dated 19 March 1850, for a churn-dasher of two L-shaped tubes of triangular section, running from near the cover down and in to the spindle, their horizontal arms perforated "through which air enters the milk during the revolution of the dasher." Between each upright arm and the axis, standards carry "whirls B, or wheels having inclined spokes," free to turn in planes through the axis. A bevel wheel and pinion turn the dasher fast, and "the friction thus produced by the whirls greatly facilitates the separation of the butter."
This rung estimates how the whirls spin, then prints the hollow frame and two whirls, fits them in a bucket, and makes butter.
Fortgeschritten
About 4 hours, plus printing
Anweisungen
1
1
How the whirls spin
How the whirls spin
Jupyter-Notebook wird geladen …
2
2
Beaters that turn on their own axes before it
Beaters that turn on their own axes before it
The embedded blueprint gears its rollers to a fixed wheel. Routzahn's whirls have no gearing: the milk spins them.
3
3
Read US 7,199
Read US 7,199
"The dasher thus receives a rapid rotating motion, and the whirls in passing through the milk are rapidly turned by its pressure upon the inclined faces of their arms which reacting upon the milk through which they pass, subdivides the whole mass and puts it in violent agitation, during which air is supplied through the outer tubes."
4
4
Print the parts
Print the parts
Print the frame flat on its side in one piece with supports: two hollow triangular L-tubes, perforated along their horizontal arms and open at the top, the top bar, and standards for the whirls. Print two whirls and the crank arm. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materialien für diesen Schritt:
PETG-Filament1 StückBenötigte Werkzeuge:
FDM-3D-Drucker5
5
Print the frame
6
6
Print the whirl
7
7
Print the crank arm
Print the crank arm
The crank arm, printed as step 4 describes.
8
8
Hang the whirls
Hang the whirls
Set each whirl between its standards and pass a 3 mm stainless rod through the standards and the whirl's hub as its axle; it must spin freely. Blow through each tube's top to check the arm holes are clear.
Materialien für diesen Schritt:
Rundstahl (Baustahl)1 StückBenötigte Werkzeuge:
Bügelsäge (Metallsäge)
Schleifpapier9
9
Spindle and crank
Spindle and crank
Pass a 10 mm square hardwood spindle through the frame's hubs and glue it. Stand it in a seat drilled in the centre of a food-grade bucket's floor, through a plywood lid, and glue the crank arm and a dowel handle on top. Keep the tubes' open tops above the cream.
Materialien für diesen Schritt:
Hartholzdübel1 Stück
20-Liter-Eimer1 Stück
Sperrholzplatte1 Stück
Holzleim1 StückBenötigte Werkzeuge:
Akkubohrschrauber
Bohrersatz
Handsäge10
10
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the bucket cut away to show the frame of two triangular L-tubes on the spindle, their perforated horizontal arms, and a free whirl on its axle between standards in each half.
11
11
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, below the tubes' open tops. Crank steadily and watch the whirls spin; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materialien für diesen Schritt:
Schlagsahne2000 ml
Grobes Meersalz1 Stück
Wasser1 StückBenötigte Werkzeuge:
Einsteck-Fühlerthermometer
Stoppuhr
Digitale Küchenwaage
Große Rührschüssel aus Edelstahl12
12
Whirls that won't spin, cream in the tubes
Whirls that won't spin, cream in the tubes
Whirl-frame air dasher troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Nathaniel Routzahn** of Middletown, Frederick County, Maryland, received US 7,199, dated 19 March 1850. He did not limit himself to the bevel wheel and pinion: "a belt running on pulleys, or an ordinary cog wheel and pinion can be used for the same purpose." He claimed the combination of the whirls with the revolving frame dasher.
**Honest limits.** Our crank turns the spindle directly, without his bevel gearing, so the frame and whirls turn slower; printed parts and a bucket stand in for his. The notebook gives an upper bound. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Materialien
9- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
- 2000 mlPlatzhalter
- 1 StückPlatzhalter
- 1 StückPlatzhalter
Benötigte Werkzeuge
10- Platzhalter
- Platzhalter
- Platzhalter
- 1 vendor sell this, none ship to you yetPlatzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
- Platzhalter
Designdateien
4Dieser Bauplan stellt her
Verwandte Blueprints
Diese Blueprints teilen Wissen — Techniken, Materialien oder Prinzipien
Self-Turning Roller Churn: Fluted Rollers Spun by a Fixed Wheel as the Dasher Turns
von Martin
ESSEN & GETRÄNKE
35
0
0
0
0
0
Spiral-Float Air-Arm Churn: A Perforated Screw Over a Breathing Wedge
von YourGrandma
ESSEN & GETRÄNKE
36
0
0
0
0
0
Double-Motion Dasher Churn: One Crank Spins One Dasher and Plunges the Other
von Emma
ESSEN & GETRÄNKE
29
0
0
0
0
0
CC0 Gemeinfrei
Dieser Blueprint ist unter CC0 veröffentlicht. Sie dürfen dieses Werk für jeden Zweck frei kopieren, ändern, verbreiten und verwenden, ohne um Erlaubnis zu fragen.
Unterstützen Sie den Maker, indem Sie Produkte über seinen Blueprint kaufen, wo er eine Maker-Provision von Anbietern festgelegt, verdient. Oder erstellen Sie eine neue Iteration dieses Blueprints und verbinden Sie ihn in Ihrem eigenen Blueprint, um Einnahmen zu teilen.