ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE
Cone-Bowl Roller Butter Worker: Roll a Conical Stick Round a Conical Bowl, the Buttermilk Drains Below
Williams worked the buttermilk out of fresh butter by rolling a stick round a cone.
I. M. Williams of Blanchester, Clinton County, Ohio, received US 12,366, dated 6 February 1855, for an "Improved Butter-Dresser": a round bowl of tin or wood "tapering from top to bottom, say top four times the diameter of bottom," with a small hole in its bottom bushed with bone, set in a rim with four legs and a brace; and a round working stick nearly filling the bottom, with a bone pin that nearly fills the hole. Rolled round the bowl, the stick presses the butter while the buttermilk sinks and escapes through the hole, "while the butter is pushed from the hole all the while."
This rung works out the bowl's proportions, then prints the bowl, bush, roller, rim and brace, builds the stand, and dresses butter.
Principiante
About 2 hours, plus printing
Instrucciones
1
1
Four times across
Four times across
Cargando el cuaderno de Jupyter…
2
2
Working butter by hand before it
Working butter by hand before it
The embedded blueprint works butter on an inclined tray with a lever. Williams rolls a conical stick round a conical bowl and drains the buttermilk through its point.
3
3
Read US 12,366
Read US 12,366
"To dress a batch of butter right from the churn, take the butter dresser, place in the working stick, put in the butter, lay your hand on top of the working stick, roll it around with the circle of the bowl, backward or forward, across or otherwise, through the butter, which will cause all the butter milk, or water that may be used, to sink directly to the bottom of the bowl and escape through the hole."
4
4
Print the parts
Print the parts
Print the bowl on its rim, the bush, the roller with its pin, standing on its wide end, the rim and the brace. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materiales para este paso:
Filamento PETG1 piezaHerramientas necesarias:
Impresora 3D de filamento (FDM)5
5
Print the bowl
6
6
Print the bush
7
7
Print the roller
Print the roller
The roller, printed as step 4 describes.
8
8
Print the rim
9
9
Print the brace
Print the brace
The brace, printed as step 4 describes.
10
10
The stand
The stand
Cut four 22 mm hardwood dowels about 260 mm long as legs. Glue their tops into the rim's sockets and their middles through the brace's sockets so the brace sits about 120 mm below the rim. Drop the bowl into the rim so its foot rests in the brace's ring, and press the bush into its bottom hole.
Materiales para este paso:
Espigas de madera dura1 pieza
Cola de carpintero1 piezaHerramientas necesarias:
Serrucho
Papel de lija11
11
The working stick
The working stick
Glue a 22 mm hardwood dowel into the roller's socket as the handle, long enough to stand well above the bowl, and round its top for the palm.
Materiales para este paso:
Espigas de madera dura1 piezaCola de carpintero1 piezaHerramientas necesarias:
SerruchoPapel de lija12
12
The patent drawing
The patent drawing
US 12,366 drawing sheet, public domain (expired patent).
13
13
Churn, then dress the butter
Churn, then dress the butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Churn 1 litre in any churn until the butter comes, and drain it. Set a jug under the bowl's hole. Put the butter in the bowl, lay your hand on the stick's top and roll it round, forward and back, so the buttermilk sinks and runs out below. Pour a little cold water over it and roll on until the water runs clear; work in a pinch of salt and weigh the butter.
Materiales para este paso:
Crema de leche espesa1000 ml
Sal marina gruesa1 pieza
Agua1 piezaHerramientas necesarias:
Termómetro de sonda permanente
Cronómetro
Báscula digital de cocina
Bol grande de acero inoxidable14
14
A hole that clogs, a stick that skids
A hole that clogs, a stick that skids
Cone-bowl butter worker troubleshooting.
Flow
Loading...
15
15
History and honest limits
History and honest limits
**I. M. Williams** of Blanchester, Clinton County, Ohio, received US 12,366, dated 6 February 1855; the title is "Butter-Worker," and the text calls it a butter-dresser. The text marks the bowl A, the figures a. Williams wrote that butter dressed without water is better flavoured and keeps sweet much longer, "a fact admitted by all"; that is the inventor's claim, not tested here. He claimed a hollow cone combined with a conical roller working on its apex.
**Honest limits.** A printed bowl, bush and pin stand in for his tin or wood and bone; the quarter-full estimate is ours. FDM prints hold food in their layer lines, so wash well and replace when worn. Your weights are the result.
Materiales
6- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
- 2 piezasMarcador de posición
- 1000 mlMarcador de posición
- 1 piezaMarcador de posición
- 1 piezaMarcador de posición
Herramientas requeridas
7- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Archivos de diseño
5Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
Ice-Drawer Butter Worker: An Ice Box Under the Tray, a Worker With Acute Edges
por YourGrandma
Carpintería
30
0
0
0
0
0
Post-and-Float Butter-Working Churn: Floats Revolving Astride Fixed Posts
por Woody
Carpintería
32
0
0
0
0
0
Churning Butter from Cream — The 5,000-Year-Old Fat Separation
por TheChef
ARTESANÍA
54
0
0
0
0
0
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.