ARTE
BELLEZA Y BIENESTAR
ARTESANÍA
CULTURA E HISTORIA
ENTRETENIMIENTO
MEDIO AMBIENTE
COMIDA Y BEBIDAS
INGENIERÍA INVERSA
CIENCIAS
DEPORTES
TECNOLOGÍA
TECNOLOGÍA VESTIBLE

Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads
A barrel is the cooper's closed vessel: oak staves held by hoops, bulging at the middle, with flat heads set in grooves at both ends. Coopers heat the staves to bend them. Shape staves wider at the middle than the ends, raise them in a hoop, heat them over a small fire and draw the open end together, drive the hoops, and fit the heads.
The picture: a new oak barrel in a cooper's workshop, with iron hoops on the floor.
Avanzado
Several days
Instrucciones
1
1
Shape the staves
Shape the staves
Rive and shave oak staves as for the vat, but taper each from the middle toward both ends, and hollow the inside face a little.
Materiales para este paso:
Tabla de madera dura8 piezasHerramientas necesarias:
Hendidor (froe)
Banco de doladura
Cuchilla de dos mangos
Cepillo de carpintero2
2
Raise and fire
Raise and fire
Stand the staves inside one hoop to form a skirt. Light a small charcoal fire inside, wet the outside, and as the staves warm, draw the open end together with a rope round it until a hoop can be driven on.
Materiales para este paso:
Carbón vegetal3 as required
Agua10 litrosHerramientas necesarias:
Aro de hierro
Cabo resistente
Martillo de peña transversal
Guantes resistentes al calor3
3
Hoops
Hoops
Drive the rest of the iron hoops on, two near each end and two at the quarters, until the joints close tight.
Materiales para este paso:
Aro de hierro6 piezasHerramientas necesarias:
Martillo de peña transversal4
4
Ends and grooves
Ends and grooves
Level the ends and bevel the inside edge with the adze, then cut a groove round the inside near each end.
Herramientas necesarias:
Azuela
Juego de formones5
5
Heads and bung
Heads and bung
Join planks into two boards, scribe circles to fit the grooves, cut and bevel them, slack the end hoops and spring the heads in. Bore a bung hole in the middle stave. Fill with water to swell it tight.
Materiales para este paso:
Tabla de madera dura2 piezas
Agua50 litrosHerramientas necesarias:
Compás de puntas
Serrucho
Cepillo de carpintero
Martillo de peña transversal
Taladro de mano6
6
Capacity of a barrel
Capacity of a barrel
Cargando el cuaderno de Jupyter…
Materiales
4- 10 piezasMarcador de posición
- 3 as requiredMarcador de posición
- 60 litrosMarcador de posición
- 6 piezasMarcador de posición
Herramientas requeridas
13- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
- Marcador de posición
Este plano hace
Blueprints relacionados
Estos blueprints comparten conocimiento — técnicas, materiales o principios
CC0 Dominio público
Este Blueprint se publica bajo CC0. Eres libre de copiar, modificar, distribuir y usar este trabajo para cualquier propósito, sin pedir permiso.
Apoya al Maker comprando productos a través de su Blueprint, donde gana una Comisión del Maker establecida por los vendedores, o crea una nueva iteración de este Blueprint e inclúyela como conexión en tu propio Blueprint para compartir ingresos.


