Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)
Forge

Créé par

Forge

13. novembre 2026NO
8
0
0
0
0

Foot-Fed Carriage Saw Table: The Saw Rides on Balls Under the Table, a Foot Lever Pulls It Through the Work (Hall, 1933)

Harry O. Hall of Murray, Utah, received US 1,930,168, dated 10 October 1933, for a portable saw table where the saw moves and the work stays still. The saw and its motor hang from a carriage under the top. The carriage rolls on balls in V-shaped tracks in a straight line. A foot lever pulls it back through a board held against the fence, and springs bring it forward again. Nuts on a hanging stem set the depth, and a spring under the motor keeps the belts tight. The table rolls on wheels and its back legs fold. The patent gives no sizes; every size here is ours, and our top is plywood where his is folded sheet metal.
Avancé
About 1 week

Consignes

1

The foot lever, the travel and the cut

Chargement du notebook Jupyter…
2

Read US 1,930,168

"The movable saw carriage is mounted to freely move longitudinally of the table in a straight line and is moved into engagement with the piece of work held in position by the work fence, when the lever 29' is depressed by the foot."
3

Table and legs

Make the top 5 of 18 mm plywood 1000 x 600 mm with pine aprons 6, 7 round it, and cut a slot 47 12 mm wide and 500 mm long down its middle. Fix four pine legs 9, 10 splayed outwards at the corners with braces 11 and plywood gussets 12, the top 850 mm high; bolt the rear legs' gussets with one bolt each as a pivot and a second removable bolt, so they fold. Put an axle 15 between the front legs with a wheel 14 on each end.

Matériaux pour cette étape :

Panneau de contreplaquéPanneau de contreplaqué1 pièce
Bois de pinBois de pin6 pièces
Barre ronde en acier douxBarre ronde en acier doux1 pièce
Jeu de roues en caoutchoucJeu de roues en caoutchouc1 pièce
Boulon de carrosserieBoulon de carrosserie8 pièces
Vis à boisVis à bois40 pièces
Colle à boisColle à bois1 pièce

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Serre-joint à pompeSerre-joint à pompe
Équerre combinéeÉquerre combinée
Mètre rubanMètre ruban
4

Tracks and carriage

Screw a pine rail 22 along each side under the top and bolt a length of steel angle on it, V upwards, as the track 21. Make the carriage of two more angles 16, V downwards over the tracks, joined near each end by a cross bolt 17 with nuts 19 either side of each angle, so their spacing can be set. Under each end of each carriage angle, between the bolt and a small steel lug 23 bolted inside the angle, put a 10 mm steel ball 20 to roll in the track. Hook two springs 24 from the front wall of the top to the front cross bolt.

Matériaux pour cette étape :

Bois de pinBois de pin1 pièce
Cornière en acier douxCornière en acier doux2 pièces
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale12 pièces
Tige filetéeTige filetée1 pièce
Écrou hexagonalÉcrou hexagonal8 pièces
Plat en acier douxPlat en acier doux1 pièce
Roulements à billesRoulements à billes1 pièce
Ressort de tractionRessort de traction2 pièces
Vis à boisVis à bois16 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Meuleuse d'angleMeuleuse d'angle
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de limesJeu de limes
Étau d'établiÉtau d'établi
Clé à moletteClé à molette
Lunettes de sécuritéLunettes de sécurité
5

Foot lever and chain

Pivot a hardwood foot lever 29' on the front axle, reaching back along the floor, with a pedal 31 on its free end. Fix a pulley 28 on a shaft 29 between the rear legs. Run a chain 27 from the rear cross bolt of the carriage over the pulley and down to the lever, fixed 450 mm from its pivot. Pressing the pedal pulls the carriage back; letting go, the springs return it.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
PouliePoulie1 pièce
Barre ronde en acier douxBarre ronde en acier doux1 pièce
Chaîne à rouleauxChaîne à rouleaux1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale3 pièces

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Scie à métauxScie à métaux
Clé à moletteClé à molette
6

Saw frame, arbor and shield

Bolt a rectangle of steel angle as the saw frame 32. Hang one end on the rear cross bolt between two collars 33 with set screws 34, so it can be slid sideways. On the front cross bolt put a sleeve 35 between collars 36 with a threaded stem 38 hanging from it, through a hole 39 in the frame's end, with a clamping nut 40 above and below: these set the saw's height. Bolt two flange bearings 42 across the frame and fit a 30 mm arbor 43 turned with a collar, a loose flange and an M20 thread; put the 250 mm blade on one end, centred under the slot, and a V-belt pulley 49 on the other. Bend a sheet steel shield 48 round the lower half of the blade and bolt it to the frame.

Matériaux pour cette étape :

Cornière en acier douxCornière en acier doux1 pièce
Barre ronde en acier douxBarre ronde en acier doux2 pièces
Vis sans tête à bout cuvetteVis sans tête à bout cuvette4 pièces
Tige filetéeTige filetée1 pièce
Écrou hexagonalÉcrou hexagonal4 pièces
Palier appliquePalier applique2 pièces
Circular Saw Blade SetCircular Saw Blade Set1 pièce
Poulie pour courroie trapézoïdale (section A)Poulie pour courroie trapézoïdale (section A)1 pièce
Tôle d'acier douxTôle d'acier doux1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale10 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Meuleuse d'angleMeuleuse d'angle
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de tarauds et filièresJeu de tarauds et filières
Tourne-à-gaucheTourne-à-gauche
Tour à métauxTour à métaux
Mandrin de tour à 3 morsMandrin de tour à 3 mors
Outil de coupe pour tourOutil de coupe pour tour
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
Cisaille à tôleCisaille à tôle
Étau d'établiÉtau d'établi
Clé à moletteClé à molette
Jeu de clés AllenJeu de clés Allen
7

Motor frame

Bolt a shorter angle frame 53 inside the saw frame, pivoted on the same rear cross bolt, and bolt the motor 51 under it with a V-belt pulley 50 in line with the arbor's. Hang its free end from a bolt 55 off a sleeve 56 on a rod 57 across the saw frame, with a spring 61 and washer 62 on the bolt above the motor frame and a nut 59 below. Fit the belt 52 and set its tension with the nut. Have the motor wired to a switch at the front.

Matériaux pour cette étape :

Cornière en acier douxCornière en acier doux1 pièce
Moteur électriqueMoteur électrique1 pièce
Poulie pour courroie trapézoïdale (section A)Poulie pour courroie trapézoïdale (section A)1 pièce
Courroie trapézoïdale (section A)Courroie trapézoïdale (section A)1 pièce
Barre ronde en acier douxBarre ronde en acier doux1 pièce
Tige filetéeTige filetée1 pièce
Coil SpringCoil Spring1 pièce
Rondelle plateRondelle plate2 pièces
Écrou hexagonalÉcrou hexagonal2 pièces
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale6 pièces
Interrupteur marche/arrêtInterrupteur marche/arrêt1 pièce

Outils nécessaires :

Scie à métauxScie à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Clé à moletteClé à molette
Jeu de clés AllenJeu de clés Allen
8

Fence and first cut

Fix a hardwood fence 63 across the top near its rear end, standing past both sides, held by hook bolts 64 that hook under steel flanges 66 screwed to the gussets, with nuts 67. Set the blade 10 mm above the board's thickness with the stem's nuts. Hold a board against the fence, start the motor and press the pedal: the saw comes back through the board. Let the pedal up and it returns.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce
Tige filetéeTige filetée1 pièce
Écrou hexagonalÉcrou hexagonal2 pièces
Plat en acier douxPlat en acier doux1 pièce
Vis à boisVis à bois8 pièces

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Équerre combinéeÉquerre combinée
Lunettes de sécuritéLunettes de sécurité
Protection auditive (casque, SNR 30 dB)Protection auditive (casque, SNR 30 dB)
9

Troubleshooting

Carriage saw troubleshooting.

Flow

Loading...
10

History and honest limits

**Harry O. Hall** of Murray, Utah, US 1,930,168, dated 10 October 1933, filed 21 March 1933. He claimed a top with a longitudinal slot, "a traveling carriage mounted beneath said top and movable longitudinally thereof", a saw frame pivoted on one cross bar and hung from the other on a stem with nuts above and below, and a motor frame hung from the saw frame on a bolt with a spring. His top is folded sheet metal on splayed legs; ours is plywood on pine. His balls are confined between the cross bolts and lugs; ours the same, in steel angle. He gives no sizes; every size here is ours.

Matériaux

27

Outils requis

22

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...