Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Saddle Breastplate: Rounded Side Straps, Neck Strap and Girth Strap on Covered Rings (Hasluck, Saddlery, 1904)
Tex

Créé par

Tex

13. novembre 2026FO
6
0
0
0
0

Saddle Breastplate: Rounded Side Straps, Neck Strap and Girth Strap on Covered Rings (Hasluck, Saddlery, 1904)

A breastplate stops a riding saddle sliding backwards, as a crupper stops it sliding forwards. This is the hunting saddle breastplate from Paul N. Hasluck's Saddlery (1904): two rounded side straps from the shoulders to a ring at the chest, a cross strap over the neck, two small buckle straps to the saddle staples, and a strap between the forelegs to the girth. Every size is his.
Avancé
About 1 day

Consignes

1

His sizes in centimetres

Chargement du notebook Jupyter…
2

Read Saddlery, ch. V

"Breastplates (Fig. 10) are made for hunting saddles to prevent them falling backwards, just as the crupper keeps them from advancing too far."
3

Get the rings and buckles

You need one 1-1/2 in covered ring, two 1 in covered rings, two 5/8 in covered buckles and one 1 in covered buckle.

Matériaux pour cette étape :

Anneau gainéAnneau gainé3 pièces
Boucle gainéeBoucle gainée3 pièces

Outils nécessaires :

Mètre rubanMètre ruban
4

Make the two side straps

Cut two side straps 7/8 in wide and 2 ft long when turned over the rings at each end. Round the top on the groove board, stuffing it with strands of soft cord. Stitch them along both sides very finely with silk cotton or linen thread, putting a 1 in ring at one end of each and both other ends into the 1-1/2 in ring. Polish the edges well after stitching.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
CordeletteCordelette1 pièce
Fil de linFil de lin1 pièce
Cire d'abeilleCire d'abeille1 pièce
Anneau gainéAnneau gainé3 pièces

Outils nécessaires :

Couteau à cuirCouteau à cuir
Planche à rainuresPlanche à rainures
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
Lissoir à arêtes de cuirLissoir à arêtes de cuir
Mètre rubanMètre ruban
5

Make the cross strap

Cut a 1-3/8 in strap to be 10 in long when bent over the rings at each end; shave the ends and prick the sides finely like the shoulder piece. Cut another piece 9-1/4 in long when bent for the rings, 7/8 in wide at both ends and widening gradually to 1-3/4 in in the centre. Put the chapes in the 1 in rings and stitch both pieces together.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Fil de linFil de lin1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Griffe à frapperGriffe à frapper
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
Mètre rubanMètre ruban
6

Make the two buckle straps

Make two 5/8 in straps 2 ft long, one end prepared for the buckle, the other narrowed; edge, rub and crease them with a hot checker. Put one in each 1 in ring to within 3 in of the buckle. Double the 3 in length with the buckle on top and make two loops between the two leathers. Stitch from the ring along both sides to the buckle, fastening the loops at the same time. Finish the edges of the stitched part and make seven or eight holes in the points.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Boucle gainéeBoucle gainée2 pièces
Fil de linFil de lin1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Abat-carreAbat-carre
Lissoir à arêtes de cuirLissoir à arêtes de cuir
PlioirPlioir
Chalumeau à propaneChalumeau à propane
Mandrin à passantsMandrin à passants
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Emporte-pièce pour cuirEmporte-pièce pour cuir
7

Make the girth strap

Cut a strap 1-1/4 in wide and 3 ft long. Narrow it to 1 in at 1 ft from the bend at the ring and turn it down for the 1 in buckle at the narrow end; edge, rub and crease it, then put the buckle in the reverse way. Cut eight or nine holes, beginning about 8 in from the buckle, and buckle the strap back on itself to make a loop for the girth (bellyband) to pass through.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Boucle gainéeBoucle gainée1 pièce
Fil de linFil de lin1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
Abat-carreAbat-carre
Lissoir à arêtes de cuirLissoir à arêtes de cuir
PlioirPlioir
Chalumeau à propaneChalumeau à propane
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Emporte-pièce pour cuirEmporte-pièce pour cuir
8

Fit the safe

Put the other end of the girth strap in the 1-1/2 in ring. Cut a safe to go under it, running up under the ring round the top part and down about 3-1/2 in below the bend, narrowing towards the end almost to the width of the strap. Crease the safe and place it under the chape and ring; stitch it down on both sides with a fancy stitch in the centre. Line the safe with chamois or very thin buff, stitched in all round, stuff a little flock through the opening at the bottom, and close the opening with fancy stitching such as an arrow point. He adds that it can be made of single leather without lining, only the bends being stitched.

Matériaux pour cette étape :

Cuir de harnaisCuir de harnais1 pièce
Peau de chamoisPeau de chamois1 pièce
Bourre de laineBourre de laine1 pièce
Fil de linFil de lin1 pièce
Cire d'abeilleCire d'abeille1 pièce

Outils nécessaires :

Couteau à cuirCouteau à cuir
PlioirPlioir
Chalumeau à propaneChalumeau à propane
AlêneAlêne
Deux aiguilles de sellierDeux aiguilles de sellier
Pince de sellierPince de sellier
9

Put it on the horse

The long side straps run down from the shoulder to the chest, and the short cross strap passes over the neck at the top. The two small straps buckle to the staples in front of the saddle, and the girth strap runs from the big ring under the belly between the forelegs to the girth.
10

Troubleshooting

Breastplate troubleshooting.

Flow

Loading...
11

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter V, "Saddle Cruppers, Breastplates, and Other Accessories", breastplates, pp. 41-44, Fig. 10; every fraction was read on the scan. He says the cross strap is pricked "like the shoulder piece" without describing a shoulder piece; check the cross strap against Fig. 10. The crupper, martingale, girths, stirrup leathers and saddle cloths of the same chapter are not made here. The tools and metric figures are ours.

Matériaux

8

Outils requis

13

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...