Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)
Woody

Créé par

Woody

13. novembre 2026NO
6
0
0
0
0

Skis: Ash or Hickory Planks Shaped to an 8 ft Pattern, Steam-Bent Tips and a Running Groove (Boy Mechanic, 1919)

Stillman Taylor's skis from The Boy Mechanic, Book 3 (1919): "far easier than snowshoe construction, since each runner is made from a single piece of plank". Ash or hickory is cut to his 8 ft pattern, thinned from the top only, the tips steamed to a 6 in bend, a centre groove cut, and the skis oiled and waxed.
Intermédiaire
About 1 week

Consignes

1

Fig. 5 in centimetres, and the wax

Chargement du notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"Either hickory or ash will give satisfaction, because both are heavy woods, as well as strong and flexible." For a man of good height, 7 to 8 ft is the right length.
3

Get and choose the wood

Get two ash or hickory planks about 9 ft long and 2 in thick, from the outside of the lower trunk, with the grain running as in his Fig. 6, A/D (in ash choose open, widely spaced grain). Or split a sound, straight tree about 10 in across and clear of knots for 10 ft: axe a straight groove about 1 in deep along each side and drive small wood wedges along it; hew only enough off the outside to make the flat running surface.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur2 pièces

Outils nécessaires :

Scie égoïneScie égoïne
Mètre rubanMètre ruban
4

Lay out and saw

Make a paper pattern from his Fig. 5 (8 ft ski): 3-3/8 in wide at the heel, 3-1/8 in at the foot, 4 in at the bend, rounding to the toe. Trace it on the plank and saw out; on green wood make the width about 1/4 in greater for shrinkage.

Matériaux pour cette étape :

Planche de bois durPlanche de bois dur1 pièce

Outils nécessaires :

CrayonCrayon
Scie égoïneScie égoïne
Mètre rubanMètre ruban
5

Plane to thickness

Plane the running surface perfectly smooth, grain straight from point to heel. Work the thickness down from the top side only, never the bottom: about 1/2 in at the heel, 3/4 in at the foot and 1/2 in at the bend.

Outils nécessaires :

RabotRabot
VastringueVastringue
6

Steam the tip

Lay the ski over a wash boiler of boiling water and soak the tip by mopping it with the water on a cloth tied to a stick. Bend gradually over many treatments to a good 6 in bend (it finishes near 5 in, as the wood straightens a little as it dries). Hold it in a rough frame over a short log, or lash or cleat the tips to the bench, as in his Fig. 7. The arch under the foot is easily put in, and easily straightened when cold if overdone.

Outils nécessaires :

Grande marmiteGrande marmite
Balai à frangesBalai à franges
Serre-joint à pompeSerre-joint à pompe
7

Binding hole, balance and groove

Put in the hole for the foot binding. If the wood was left long, trim the heel so the ski balances when lifted by the toe straps (he sees no advantage in weighting a light heel with lead). Cut a groove in the exact centre of the running surface, about 1/8 in deep and 3/8 to 1/2 in wide, from the heel to the start of the bend, with a grooving plane or a small gouge.

Matériaux pour cette étape :

Lanière de cuirLanière de cuir2 pièces

Outils nécessaires :

Chignole à mainChignole à main
Ciseaux à boisCiseaux à bois
GougeGouge
Scie égoïneScie égoïne
8

Finish and wax

Sandpaper top and bottom and rub down with linseed oil with a little paraffin or beeswax in it; oil and wax the running surface (spar varnish on the tops if you want gloss). For a hard wax, melt 10 oz of beeswax with 5 oz of rosin, stir in 1 oz of turpentine and pour into small boxes. Rub it on and go over it with a hot flatiron; too much wax makes climbing hard.

Matériaux pour cette étape :

Papier abrasifPapier abrasif1 pièce
Huile de linHuile de lin1 pièce
ParaffineParaffine1 pièce
Cire d'abeilleCire d'abeille1 pièce
Colophane de pinColophane de pin1 pièce
TérébenthineTérébenthine1 pièce

Outils nécessaires :

Grande marmiteGrande marmite
Fer à repasser platFer à repasser plat
Brosse largeBrosse large
9

Troubleshooting

Ski troubleshooting.

Flow

Loading...
10

History and honest limits

From "How to Make Skis" by Stillman Taylor, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, pp. 27-30). His text gives the groove as 3/8 to 1/2 in wide; Fig. 5 shows 3/8 in. He does not describe the binding. The tools and metric figures are ours.

Matériaux

8

Outils requis

13

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...