Collaboration
ART
BEAUTÉ ET BIEN-ÊTRE
ARTISANAT
CULTURE ET HISTOIRE
DIVERTISSEMENT
ENVIRONNEMENT
NOURRITURE ET BOISSONS
INGÉNIERIE INVERSE
SCIENCES
SPORTS
TECHNOLOGIE
TECHNOLOGIE PORTABLE
Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)
Forge

Créé par

Forge

13. novembre 2026NO
8
0
0
0
0

Tube-Track Pedal Saw Table: Any Portable Saw Clamped Upside Down on a Carriage Rolling Inside Slotted Tubes (Tomlinson & Bearden, 1931)

William A. Tomlinson and Howell B. Bearden of Phoenix, Arizona, received US 1,813,783, dated 7 July 1931, for a table that turns any portable power saw into a table saw. The saw is clamped upside down on a carriage, its blade through the slot of a top hinged at the rear. The carriage rolls on ball-bearing rollers inside two steel tubes slotted along their undersides. A pedal pushes it forward through the work, leaving both hands free, and a spring brings it back. With the pedal left alone it works as a fixed saw, and the saw unbolts for hand use. The patent gives no sizes; every size here is ours.
Avancé
About 4 days

Consignes

1

Pedal, link and travel

Chargement du notebook Jupyter…
2

Read US 1,813,783

"By using the pedal in the manner above set forth both hands of the operator will be free for manipulating the work, which is especially desirable when pattern work is to be sawed."
3

Angle-iron frame

Bolt a frame of steel angle 900 x 500 mm, 850 high: four corner legs 1, side and end bars 2, 3 halfway up and 4, 5 at the top, flat-bar diagonal braces 6 at the top corners, a cross bar 7 between the rear legs above the middle bars, and a cross bar 8 between the front legs at the bottom. Drill a vertical row of 9 mm holes 13, 25 mm apart, near the top of each leg, for the track hangers.

Matériaux pour cette étape :

Cornière en acier douxCornière en acier doux6 pièces
Plat en acier douxPlat en acier doux1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale40 pièces
Écrou hexagonalÉcrou hexagonal40 pièces
Rondelle plateRondelle plate40 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Meuleuse d'angleMeuleuse d'angle
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
PointeauPointeau
Équerre combinéeÉquerre combinée
Mètre rubanMètre ruban
Clé à moletteClé à molette
Lunettes de sécuritéLunettes de sécurité
4

Slotted tube tracks

Cut two 900 mm lengths of 42 mm steel tube 9, 10 and cut a 10 mm slot 14 along the underside of each, stopping 20 mm short of the ends; file the slot's edges smooth. Bolt a flat-bar hanger 11 to each end of each tube and hang the tubes along the frame's sides from the legs with bolts 12 through the row of holes, at the height that suits your saw. Put a short coil spring 39 in each end of each tube as a buffer.

Matériaux pour cette étape :

Tube rond en acier douxTube rond en acier doux2 pièces
Plat en acier douxPlat en acier doux1 pièce
Coil SpringCoil Spring4 pièces
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale8 pièces
Écrou hexagonalÉcrou hexagonal8 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Meuleuse d'angleMeuleuse d'angle
Jeu de limesJeu de limes
Étau d'établiÉtau d'établi
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Clé à moletteClé à molette
Pied à coulisse numérique 6 poucesPied à coulisse numérique 6 pouces
Lunettes de sécuritéLunettes de sécurité
5

Carriage and rollers

Cut the carriage 30 from 5 mm steel plate, as wide as between the tubes. At each corner bolt an upright flat-bar standard 31 that reaches up through a tube's slot, and on its top a short bar 33 across inside the tube carrying a 22 mm ball bearing 32 at each end on an M8 bolt with a lock nut. Slide the rollers into the tubes from the ends, the standards hanging down through the slots, and bolt them to the carriage.

Matériaux pour cette étape :

Plaque d'acier douxPlaque d'acier doux1 pièce
Plat en acier douxPlat en acier doux1 pièce
Roulement à billesRoulement à billes8 pièces
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale16 pièces
Écrou frein à bague nylonÉcrou frein à bague nylon8 pièces
Rondelle plateRondelle plate16 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Meuleuse d'angleMeuleuse d'angle
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Jeu de limesJeu de limes
Étau d'établiÉtau d'établi
Clé à moletteClé à molette
6

Pedal and springs

Pivot a lever 21 of steel flat bar on the front bottom cross bar 8, with an arm 22 to the side carrying the pedal 20 and a brace 23 from arm to lever. Join the lever's top to the carriage's front with a flat-bar link 24. Hook a return spring 25a from the rear cross bar 7 to the lever partway up.

Matériaux pour cette étape :

Plat en acier douxPlat en acier doux2 pièces
Barre ronde en acier douxBarre ronde en acier doux1 pièce
Ressort de tractionRessort de traction1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale4 pièces
Écrou frein à bague nylonÉcrou frein à bague nylon4 pièces

Outils nécessaires :

Scie à métauxScie à métaux
Perceuse à colonnePerceuse à colonne
Jeu de foretsJeu de forets
Étau d'établiÉtau d'établi
Clé à moletteClé à molette
7

Mount the saw and the top

Turn the circular saw upside down on the carriage and bolt it by its base plate with bolts and wing nuts, so it lifts off for hand use; his T-bolt 34 and hook bolts 36 gripped the saw's handles, which modern saws do not suit. Make the top 42 of plywood on a steel angle frame 44, slotted along the blade's path, and hinge its rear edge to the frame so it swings up to reach the saw. Fit a catch 47 to lock it down and a folding flat-bar brace 49 to prop it up.

Matériaux pour cette étape :

Scie circulaireScie circulaire1 pièce
Assortiment de boulons à tête hexagonaleAssortiment de boulons à tête hexagonale4 pièces
Écrou papillonÉcrou papillon4 pièces
Panneau de contreplaquéPanneau de contreplaqué1 pièce
Cornière en acier douxCornière en acier doux1 pièce
Charnière à lameCharnière à lame2 pièces
Agrafe et porteAgrafe et porte1 pièce
Plat en acier douxPlat en acier doux1 pièce
Vis à boisVis à bois16 pièces

Outils nécessaires :

Scie sauteuseScie sauteuse
Perceuse sans filPerceuse sans fil
Jeu de foretsJeu de forets
Scie à métauxScie à métaux
Clé à moletteClé à molette
Équerre combinéeÉquerre combinée
8

Cut

Lock the top down. Set the saw's depth so the blade stands 10 mm above the board. Place the board on the top in front of the blade, start the saw and press the pedal: the carriage rolls the running blade through it while both hands hold the work. Let the pedal up and the spring returns it. For ripping, leave the carriage still and feed the board.

Outils nécessaires :

Lunettes de sécuritéLunettes de sécurité
Protection auditive (casque, SNR 30 dB)Protection auditive (casque, SNR 30 dB)
9

Troubleshooting

Tube-track saw table troubleshooting.

Flow

Loading...
10

History and honest limits

**William A. Tomlinson** and **Howell B. Bearden** of Phoenix, Arizona, US 1,813,783, dated 7 July 1931, filed 5 December 1928. They claimed a top with a slot, "laterally spaced longitudinally extending tubular tracks" below it, "slotted longitudinally on their lower faces", and a saw carriage with upstanding roller-carrying hangers in the tracks, their shanks through the slots. Their saw is held by its handles; ours by its base plate. Their frame is angle iron, as ours. They give no sizes; every size here is ours.

Matériaux

18

Outils requis

15

CC0 Domaine public

Ce blueprint est publié sous CC0. Vous êtes libre de copier, modifier, distribuer et utiliser ce travail pour tout usage, sans demander la permission.

Soutenez le Maker en achetant des produits via son Blueprint où il perçoit une Commission Maker définie par les Vendeurs, ou créez une nouvelle itération de ce Blueprint et incluez-le comme connexion dans votre propre Blueprint pour partager les revenus.

Commentaires

(0)

Se connecter pour participer à la discussion

Chargement des commentaires...