Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI

Boring Bar: Driven Between Centres, with a Set-Screw Cutter (Yates, 1922)
A home-made boring bar for holes too long for an ordinary boring tool, which would spring. A short, stiff bar runs between the lathe centres, driven by a dog, and carries a hardened tool-steel cutter locked in a cross-hole by a set screw. The work is bolted to the lathe carriage and fed past the turning cutter.
Result: a boring bar, plus the small short-cut bar of Fig. 110.
Source: R. F. Yates, Lathe Work for Beginners (1922), pp. 134-136. Unknown: bar diameter and set-screw size. Picture: Figs. 110-111 of the book.
Menengah
Unknown
Instruksi
1
1
Turn the bar
Turn the bar
Turn a bar no longer than the job needs; the shorter it is, the less it twists under the cut. Drill both ends for the lathe centres. For short cuts, the small bar of Fig. 110 is 4 to 6 inches long with a round shank and a squared end. Ours: mild steel round bar. Not given: the diameter.
Material untuk langkah ini:
Batang bulat baja lunak1 boring barAlat yang dibutuhkan:
Mesin Bubut Logam
Dimensi tidak diketahui2
2
Fit the cutter and set screw
Fit the cutter and set screw
Drill a cross-hole through the bar for the cutter and drill and tap a hole into it for a set screw that locks the cutter. Make the cutter of tool steel, grind its point with proper clearance, and harden it.
Material untuk langkah ini:
Batang baja perkakas persegi1 cutter
Logam tidak diketahui1 set screwAlat yang dibutuhkan:
Mesin Bor Duduk
Set pembuat ulir
Batu asah roda
Oven perlakuan panas
Ember pendingin tempa3
3
Bore with it
Bore with it
Bolt the work down to the lathe carriage carefully and securely; carriage bolts of several sizes are handy for this. Drive the bar between centres with a dog and feed the carriage. Run very slowly when boring cast iron, and keep the feed light so the bar does not spring.
Alat yang dibutuhkan:
Mesin Bubut Logam
Baut kepala bulat leher persegiBahan
3- 1 boring barPlaceholder
- 1 cutterPlaceholder
- 1 set screwPlaceholder
Alat yang Diperlukan
8- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
- Placeholder
Bahan cetak biru terhubung

10% Atribusi
Mild Steel Bar Stock Forged from an Ingot
oleh Forge
Modern
45
0
0
0
5
0

10% Atribusi
Tool-Steel Bar: Crucible Steel Drawn Out at a Cherry-Red Heat
oleh Forge
Pandai Besi
33
0
0
0
5
0

10% Atribusi
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
oleh Forge
Alat Pengerjaan Logam
12
0
0
0
1
0
Cetak biru ini membuat
CC0 Domain Publik
Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.
Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.
