Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)
Forge

Dibuat oleh

Forge

4. November 2026NO
12
0
0
1
0

Lathe Cutting Tool: Ground to the Clearance and Slope for Each Metal (Machinery's Handbook, 1924)

A lathe turning tool ground from tool steel bar. Three things decide how well it cuts: the shape of the edge seen from above, the clearance under the edge, and the slope of the top the chip slides over. The Handbook gives the angles for each kind of metal to be turned. Variable: the metal to be turned. Clearance 8 to 10° for general work, 12 to 14° for brass. Soft steel: back slope 8°, side slope 14 to 20°. Very hard steel: 5° and 9°. Brass: flat on top. Source: Machinery's Handbook (1924), pp. 887-889, Tool Grinding. Unknown: the steel and the bar size. Picture: the Handbook's figure.
Menengah
Unknown

Instruksi

1

Choose the edge shape

Grind the edge, seen from above, to suit the job. A large-radius edge roughs and keeps its edge at higher speed; a smaller point is better on flexible work that would chatter. A parting tool must be widest at the cutting edge so it does not bind in its groove. Ours: square tool steel bar. Not given: the steel, the bar size.

Material untuk langkah ini:

Batang baja perkakas persegiBatang baja perkakas persegi1 tool blank

Alat yang dibutuhkan:

Batu asah rodaBatu asah roda
AirAir
2

Grind the clearance and the slope

Grind clearance under the edge: 8 to 10° for general turning, 12 to 14° for brass and soft metals; too much weakens the edge. Slope the top away from the working part of the edge. A roughing tool for medium or soft steel gets a back slope of 8° and a side slope of 14 to 20°; for very hard steel, 5° and 9°. A broad finishing tool slopes straight back. Thread tools and tools for brass or chilled iron are flat on top; very hard metals get almost no slope and little clearance. Roughing tools cut fastest with a lip angle near 61°, but cast iron cuts better at about 68°.

Alat yang dibutuhkan:

Batu asah rodaBatu asah roda
Busur DerajatBusur Derajat
3

Grind without burning

Press the tool only moderately against the wheel and draw it away often, especially when grinding a broad flat face, so the edge does not overheat and burn. Keep the wheel supplied with plenty of cooling water.

Alat yang dibutuhkan:

Batu asah rodaBatu asah roda
AirAir

Bahan

1

Alat yang Diperlukan

3
  • Placeholder
  • Placeholder
  • Placeholder

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...