Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

Dibuat oleh

Tinny

13. November 2026US
8
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
Pemula
About 2 hours

Instruksi

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

Material untuk langkah ini:

Loyang paiLoyang pai2 buah
Timah solder pipa tanpa timbalTimah solder pipa tanpa timbal1 buah
FluksFluks1 buah

Alat yang dibutuhkan:

Solder ListrikSolder Listrik
Kikir LogamKikir Logam
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

Material untuk langkah ini:

KalengKaleng1 buah

Alat yang dibutuhkan:

Gunting logam beratGunting logam berat
Kikir LogamKikir Logam
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

Material untuk langkah ini:

Timah solder pipa tanpa timbalTimah solder pipa tanpa timbal1 buah
FluksFluks1 buah

Alat yang dibutuhkan:

Bor tanganBor tangan
Kikir LogamKikir Logam
Solder ListrikSolder Listrik
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

Material untuk langkah ini:

Kawat besiKawat besi1 buah
Timah solder pipa tanpa timbalTimah solder pipa tanpa timbal1 buah
FluksFluks1 buah

Alat yang dibutuhkan:

Tang Berujung RataTang Berujung Rata
Solder ListrikSolder Listrik
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

Material untuk langkah ini:

Tali KulitTali Kulit1 buah
Kait pegasKait pegas2 buah

Alat yang dibutuhkan:

Air tawarAir tawar
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

Bahan

7

Alat yang Diperlukan

6

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...