Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
Woody

Dibuat oleh

Woody

13. November 2026NO
6
0
0
0
0

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)

George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
Menengah
About 2 days

Instruksi

1

His sizes, and the rocker

Memuat notebook Jupyter…
2

Read The Boy Mechanic, Book 3

"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3

Thin the bend

Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras2 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Ketam tanganKetam tangan
Meteran GulungMeteran Gulung
PensilPensil
4

Boil and bend

If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.

Material untuk langkah ini:

Papan pinusPapan pinus1 buah

Alat yang dibutuhkan:

Panci BesarPanci Besar
Klem batangKlem batang
Ketam tanganKetam tangan
5

Set the blocks and top

For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.

Material untuk langkah ini:

Papan Kayu KerasPapan Kayu Keras1 buah
Papan pinusPapan pinus3 buah
Baut kepala bulat leher persegiBaut kepala bulat leher persegi6 buah
Ring RataRing Rata6 buah
Sekrup kayuSekrup kayu1 buah

Alat yang dibutuhkan:

Gergaji TanganGergaji Tangan
Bor tanganBor tangan
Set Mata Bor BenamSet Mata Bor Benam
PaluPalu
6

Troubleshooting

Ski sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.

Bahan

5

Alat yang Diperlukan

9
  • Placeholder
  • Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • 1 vendor sell this, none ship to you yet
    Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder
  • Placeholder

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...