Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)
Forge

Dibuat oleh

Forge

13. November 2026NO
9
0
0
0
0

Cam-Arm Tubing Cutter: Two Swinging Arms Keep the Wheel and Rollers Evenly Round Any Tube (Lutsker, 1959)

Simon Lutsker of Shaker Heights, Ohio, received US 2,870,536, dated 27 January 1959, for a tubing cutter that grips small and large tubes equally well. The wheel turns under a housing at the foot of a guide. A block slides up the guide on a screw. Two arms hang from the block, each with a roller at its lower end. Springs press the arms' curved cam edges against rollers on the housing. As the screw draws the block up, the arms swing inwards or outwards, so the wheel and the two rollers stay about evenly spaced round the tube, whatever its size. We worked out the cam so the three contacts are exactly 120 degrees apart. The curve comes out as an arc, as in his patent. All sizes are ours.
Lanjutan
About 4 days

Instruksi

1

Three points evenly round

Memuat notebook Jupyter…
2

Read US 2,870,536

"Irrespective of the size of the tubing which is being cut, the points of engagement of the cutter wheel 21 and support rollers 32 with the tubing will always be substantially equidistant from each other circumferentially of the tubing."
3

Print the template

The arm plate with its cam edge, the housing and the guide block at 1:1, with holes, slots and sizes. print at 100 % (check the 50 mm bar).
Berkas desainPDFCC0 - Free
4

Cut the arm plates

Glue four copies of the arm outline on 3 mm steel plate. Saw and file them to the line, taking the cam edge slowly and checking it against the template. Clamp them in a stack and drill the 4 mm pivot and roller-pin holes and the two 3 mm holes through all four together.

Material untuk langkah ini:

Pelat baja lunakPelat baja lunak1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Set Kikir JarumSet Kikir Jarum
Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
PenitikPenitik
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
5

Make the housing

From 30 x 20 flat bar, saw a block 64 mm long and file it to 28 x 18 mm, leaving the two ears below its middle. Saw the forked ends: two cuts 14.4 mm apart, 20 mm in from each end, and break out the middle. Saw and file a 7 mm slot up between the ears for the wheel. Drill the 5 mm shaft hole across the ears, the 4 mm housing-roller pins across the forks, and the 4 mm rivet hole. File a groove 20 mm wide and 3 mm deep down each face for the guide's legs.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
Ragum MejaRagum Meja
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
PenggoresPenggores
6

Make the block and the guide

Saw the guide block from the same bar, 60 x 18 x 28 mm, with forked ends from 14 mm out, the 4 mm pivot holes, the 3 mm spring-pin holes and the leg grooves. Drill 8.5 mm up its middle and tap M10. Bend a 20 x 3 mm flat bar into an inverted U with its legs 22 mm apart inside and 69 mm high, and drill a 10.5 mm hole in its top.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak2 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Mesin Bor DudukMesin Bor Duduk
Ragum MesinRagum Mesin
Set Mata BorSet Mata Bor
Set pembuat ulirSet pembuat ulir
Ragum MejaRagum Meja
Palu kepala bulatPalu kepala bulat
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
7

Turn the rollers and the wheel shaft

Turn two housing rollers 10 mm across and 14 mm long, and two lower rollers 12 mm across and 7.6 mm long, from mild steel bar, all bored 4.2 mm. For the wheel shaft, turn a 6 mm rod to 5 mm, leaving a 6 mm head, file a flat on the head, and turn a groove near the other end.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 buah
Batang Baja LunakBatang Baja Lunak1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Set Mata BorSet Mata Bor
Set KikirSet Kikir
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
8

Turn the cutting wheel

Chuck a tool steel bar and face it. Turn the end to 20 mm across for 10 mm, centre drill and drill a 5 mm hole 10 mm deep, and turn the edge to a 50 degree vee, 25 degrees each side, sharp in the middle of the 6 mm width. Part it off 6 mm long and take the burr off the hole.

Material untuk langkah ini:

Batang baja perkakasBatang baja perkakas1 buah

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Cekam bubut 3 rahangCekam bubut 3 rahang
Pahat bubutPahat bubut
Pahat potong bubutPahat potong bubut
Set mata bor senterSet mata bor senter
Set Mata BorSet Mata Bor
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
Kacamata pengamanKacamata pengaman
9

Harden and temper

Heat the wheel to a cherry red, until a magnet no longer sticks, and quench it in water, moving it about. Rub it bright with a stone, warm it on a piece of steel plate over the fire, and quench again as soon as it turns a light straw colour.

Alat yang dibutuhkan:

Tungku TempaTungku Tempa
Penjepit TempaPenjepit Tempa
Magnet KecilMagnet Kecil
Ember pendingin tempaEmber pendingin tempa
AirAir
Batu AsahBatu Asah
Sarung tangan lasSarung tangan las
Kacamata pengamanKacamata pengaman
10

Make the springs

From spring steel strip, cut two strips 8 mm wide and 30 mm long for the arm springs, and one 6 mm wide and 25 mm long to hold the wheel shaft. Bend each arm spring so it presses on its arm's spring pin and pushes the arm outwards. Drill a hole in the end of each for its pin or screw.

Material untuk langkah ini:

Pita baja pegasPita baja pegas1 buah

Alat yang dibutuhkan:

Gergaji BesiGergaji Besi
Set KikirSet Kikir
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Ragum MejaRagum Meja
11

Make the screw

Cut 90 mm of M10 threaded rod. Lock two nuts together 25 mm from its top as the flange. Put it up through the guide's top hole, add two washers as the spacer, then a nut locked with a second one. Drill a 6 mm hole across the top end and fit a 70 mm piece of 6 mm rod as the T-handle.

Material untuk langkah ini:

Batang berulirBatang berulir1 buah
Mur Segi EnamMur Segi Enam4 buah
Ring RataRing Rata2 buah
Batang Baja LunakBatang Baja Lunak1 buah

Alat yang dibutuhkan:

Kunci InggrisKunci Inggris
Mesin Bor DudukMesin Bor Duduk
Set Mata BorSet Mata Bor
Gergaji BesiGergaji Besi
Palu kepala bulatPalu kepala bulat
12

Assemble

Pin each arm pair together with its lower roller between the plates, and with short tubes as spacers on the pivot and spacer pins. Pin the arms into the block's forked ends. Fit the housing rollers in the housing's forks and the wheel on its shaft, with the flat spring screwed to the housing and sitting in the shaft's groove. Screw the block onto the screw, feed the arms down through the housing's forks inside its rollers, and rivet the guide's legs into the housing's grooves. Pin the arm springs to the block. Oil every pin and the screw.

Material untuk langkah ini:

Pin pasak bajaPin pasak baja8 buah
Paku keling bajaPaku keling baja1 buah
Sekrup Kepala SoketSekrup Kepala Soket1 buah

Alat yang dibutuhkan:

Palu kepala bulatPalu kepala bulat
PenitikPenitik
Ragum MejaRagum Meja
Set kunci LSet kunci L
Minyak potongMinyak potong
13

Cut a copper tube

Mark a copper tube and hold it in a vice with soft jaws, or by hand for small tubes. Turn the handle to open the arms, put the cutter over the tube, and turn it back until the rollers lift the tube against the wheel. Check by eye that the wheel and rollers look evenly spaced. Turn the cutter once round, give the screw about a quarter turn, and go on until the tube parts. The wheel should run in its own groove; the end should be square and not squeezed oval. Clean the inside of the end with a deburring tool.

Material untuk langkah ini:

Pipa tembagaPipa tembaga1 buah

Alat yang dibutuhkan:

Ragum MejaRagum Meja
Alat penghilang duri sisaAlat penghilang duri sisa
Jangka Sorong Digital 6 InciJangka Sorong Digital 6 Inci
14

Troubleshooting

Cam-arm tubing cutter troubleshooting.

Flow

Loading...
15

History and honest limits

**Simon Lutsker** of Shaker Heights, Ohio, US 2,870,536, dated 27 January 1959, filed 26 August 1957. He claimed "a guide block mounted for movement along said guide member and movable by said screw means, a pair of cammable members pivotally secured to said guide block" and the springs pressing their "arcuate cam surfaces" against the housing rollers. He said the contacts stay "substantially" equidistant; ours are set exactly 120 degrees apart. The patent gives no sizes or cam radius; all of ours are ours.

Bahan

13

Alat yang Diperlukan

29

Berkas desain

1

Cetak biru ini membuat

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...