Kolaborasi
SENI
KECANTIKAN & KESEHATAN
KERAJINAN
BUDAYA & SEJARAH
HIBURAN
LINGKUNGAN
MAKANAN & MINUMAN
REKAYASA BALIK
ILMU PENGETAHUAN
OLAHRAGA
TEKNOLOGI
PERANGKAT PAKAI
Wood Lathe: Simple Amateur's Lathe with a Maple Bed, 7 in Swing (Lathe Work for Beginners, 1922)
Woody

Dibuat oleh

Woody

4. November 2026NO
11
0
0
0
0

Wood Lathe: Simple Amateur's Lathe with a Maple Bed, 7 in Swing (Lathe Work for Beginners, 1922)

A wood-turning lathe an amateur can build: two strips of hard maple bolted to maple legs make the 3 ft bed, and cast-iron head-stock, tail-stock, hand-rest body, hand wheels and cone pulleys are cast from home-made patterns. Steel spindles turn in the cast-iron bearings, and a cone pulley drives the head-stock from a countershaft. Result: a wood lathe with a 7 in swing and a 3 ft bed. Source: R. F. Yates, Lathe Work for Beginners (1922), Chapter XII, pp. 208-216. Unknown: the pattern sizes (on the book's drawings) and the drive. Picture: Fig. 157 of the book.
Lanjutan
Unknown

Instruksi

1

Make the patterns and get castings

Make patterns from any handy wood: one for both head-stock and tail-stock, with a web joining the two bearings so the casting does not spring; one for the hand wheels (three castings); one for the washers (two); the cone pulley (two: lathe and countershaft); and the hand-rest body. Give them a slight draw taper. Have them cast in iron at a foundry. Not given: pattern sizes (on the book's drawings).

Material untuk langkah ini:

Benda cor besiBenda cor besi1 head-stock, tail-stock, wheels, washers, pulleys, rest body

Alat yang dibutuhkan:

Papan kayuPapan kayu
Tanur kubahTanur kubah
Dimensi tidak diketahuiDimensi tidak diketahui
2

Build the maple bed

Make the bed of two strips of clear hard maple 1 in thick, 4 in wide and about 36 in long (about 1 1/2 in thick for a longer bed), and two maple legs, the part between the ways cut exactly square. Bore a 5/8 in hole through the head-stock leg in line with the head-stock's 1/2 in tapped hole, recessed below for a nut and washers. Bolt bed to legs with eight 3/8 in carriage bolts. Sand it and give it a coat of clear shellac against warping. White oak will do if there is no maple.

Material untuk langkah ini:

Papan kayu kerasPapan kayu keras1 ways and legs
Baut kepala bulat leher persegiBaut kepala bulat leher persegi8 3/8 in carriage bolts
SirlakSirlak1 finish

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
AmplasAmplas
3

Machine the stocks

Face the outside ends of the head-stock and tail-stock bearings on a shaper or milling machine. Drill the bearings between centres in a lathe with a 47/64 in drill, saw off the joining web, face the inner ends and ream to 3/4 in. Line both castings up on a 3/4 in shaft and machine their bottoms. Drill oil holes in the head-stock lugs. Tap the tail-stock front lug 3/16 in for a clamp turned, heated and bent to shape, with soft copper or brass under it; tap the tail-stock rear bearing 7/8 in, 9 threads.

Material untuk langkah ini:

Logam tidak diketahuiLogam tidak diketahui1 clamp and copper pad

Alat yang dibutuhkan:

Mesin FraisMesin Frais
Mesin Bubut LogamMesin Bubut Logam
Set pembuat ulirSet pembuat ulir
Tungku TempaTungku Tempa
4

Turn the spindles and pulley

Turn the head-stock spindle from 1 3/8 in machine steel: 3/4 in diameter, a 7/8 in nose threaded 9 to the inch, a 3/8 in hole right through and a No. 1 Morse taper in the nose. Turn the tail-stock spindle from 7/8 in stock, 3/4 in diameter with a 7/8 in, 9-thread part. Centre each piece, drill halfway from each end with a 3/8 in drill, ream, then finish between centres. Turn the cone pulley with crowned faces, wide enough to run easily between the bearings, and fix it to the spindle with a 3/8 in headless set screw.

Material untuk langkah ini:

Batang bulat baja lunakBatang bulat baja lunak1 spindles
Logam tidak diketahuiLogam tidak diketahui1 set screws

Alat yang dibutuhkan:

Mesin Bubut LogamMesin Bubut Logam
Mesin Bor DudukMesin Bor Duduk
5

Fit the wheels and hand rest, and assemble

Drill hand wheel N 3/4 in for the tail-stock spindle and hold it with a 1/4 in set screw; tap the other two wheels 1/2 in. Drill the washers 9/16 in. Bolt the head-stock down with a stud through the leg, and fit a 1/2 in stud about 7 in long for the tail-stock and a 1/2 in square-headed bolt for the hand-rest body. Plane the hand rest's bottom, drill it 3/4 in, and fit tee-rests of 1/4 x 1 in flat steel welded to 3/4 in shafting, held by a 1/4 in set screw; make several lengths. The cast iron serves as bearing metal, or the bearings can be bushed or babbitted.

Material untuk langkah ini:

Besi Strip Baja LunakBesi Strip Baja Lunak1 tee-rests
Logam tidak diketahuiLogam tidak diketahui1 studs, bolts, set screws, shafting

Alat yang dibutuhkan:

Mesin Bor DudukMesin Bor Duduk
Set pembuat ulirSet pembuat ulir
Tungku TempaTungku Tempa

Bahan

7

Alat yang Diperlukan

9

CC0 Domain Publik

Cetak biru ini dirilis di bawah CC0. Anda bebas untuk menyalin, memodifikasi, mendistribusikan, dan menggunakan karya ini untuk tujuan apa pun, termasuk komersial, tanpa meminta izin.

Dukung Maker dengan membeli produk melalui Cetak Biru mereka di mana mereka mendapatkan Komisi Pembuat yang ditetapkan oleh Penjual, atau buat iterasi baru dari Cetak Biru ini dan masukkan sebagai koneksi di milik Anda sendiri.

Diskusi

(0)

Masuk untuk bergabung dengan diskusi

Memuat komentar...