همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

ایجاد شده توسط

Tinny

13. نوامبر 2026US
۹
۰
۰
۰
۰

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
مبتدی
About 2 hours

دستورالعمل‌ها

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

مواد مورد نیاز این مرحله:

ظرف پایظرف پای2 قطعه
سیم لحیم لوله‌کشی بی‌سربسیم لحیم لوله‌کشی بی‌سرب1 قطعه
فلاکس لحیمفلاکس لحیم1 قطعه

ابزارهای مورد نیاز:

هویه برقیهویه برقی
سوهان فلزسوهان فلز
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

مواد مورد نیاز این مرحله:

قوطی حلبیقوطی حلبی1 قطعه

ابزارهای مورد نیاز:

قیچی فلز سنگین‌کارقیچی فلز سنگین‌کار
سوهان فلزسوهان فلز
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

مواد مورد نیاز این مرحله:

سیم لحیم لوله‌کشی بی‌سربسیم لحیم لوله‌کشی بی‌سرب1 قطعه
فلاکس لحیمفلاکس لحیم1 قطعه

ابزارهای مورد نیاز:

دریل دستیدریل دستی
سوهان فلزسوهان فلز
هویه برقیهویه برقی
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

مواد مورد نیاز این مرحله:

سیم آهنیسیم آهنی1 قطعه
سیم لحیم لوله‌کشی بی‌سربسیم لحیم لوله‌کشی بی‌سرب1 قطعه
فلاکس لحیمفلاکس لحیم1 قطعه

ابزارهای مورد نیاز:

انبردست تختانبردست تخت
هویه برقیهویه برقی
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

مواد مورد نیاز این مرحله:

بند چرمیبند چرمی1 قطعه
قلاب فنریقلاب فنری2 قطعه

ابزارهای مورد نیاز:

آب شیرینآب شیرین
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

مواد

7

ابزارهای لازم

6

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...