همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
Woody

ایجاد شده توسط

Woody

13. نوامبر 2026NO
۶
۰
۰
۰
۰

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)

George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
متوسط
About 2 days

دستورالعمل‌ها

1

His sizes, and the rocker

در حال بارگذاری دفترچهٔ Jupyter…
2

Read The Boy Mechanic, Book 3

"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3

Thin the bend

Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت2 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
رندهٔ دستیرندهٔ دستی
متر نواریمتر نواری
مدادمداد
4

Boil and bend

If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.

مواد مورد نیاز این مرحله:

تختهٔ کاجتختهٔ کاج1 قطعه

ابزارهای مورد نیاز:

دیگ بزرگدیگ بزرگ
گیرهٔ میله‌ایگیرهٔ میله‌ای
رندهٔ دستیرندهٔ دستی
5

Set the blocks and top

For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
تختهٔ کاجتختهٔ کاج3 قطعه
پیچ سرگرد گردن‌چهارگوشپیچ سرگرد گردن‌چهارگوش6 قطعه
واشر تختواشر تخت6 قطعه
پیچ چوبپیچ چوب1 قطعه

ابزارهای مورد نیاز:

ارهٔ دستیارهٔ دستی
دریل دستیدریل دستی
ست مته خزینهست مته خزینه
چکشچکش
6

Troubleshooting

Ski sled troubleshooting.

Flow

Loading...
7

History and honest limits

From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.

مواد

5

ابزارهای لازم

9
  • جایگزین
  • جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • 1 vendor sell this, none ship to you yet
    جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین
  • جایگزین

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...