همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنیها

Cast Iron Pot: a Kettle Moulded in Loam, Bottom Up (Bolland, The Iron-Founder, 1892)
How a founder moulds an iron kettle or pot without a pattern: a brick core is built and coated with loam, swept to the inside shape with a turning board; a layer of sand swept on top stands for the metal's thickness; the cope is built over it, and the space the sand stood for is filled with iron. Bolland's example is an 8 ft kettle 1 3/4 in thick; the same steps serve any size.
Variable: the size and wall thickness, set by the sweeps.
Source: S. Bolland, The Iron-Founder (1892), pp. 180-183. Unknown: the loam mix and drying. Picture: Fig. 161 of the book.
متخصص
Unknown
دستورالعملها
1
1
Build and sweep the core
Build and sweep the core
Set the core on a foundation plate strong enough to lift it without springing: a plain plate at least 3 in thick, or a ribbed one 2 in thick. Build the core of bricks in open, coarse mud, bricks well apart so air passes, with half-bricks crossing the joints on the top course and a tie-course here and there. Scrape the joints, rub on soft loam and sweep it to shape as you go round; the first sweep also strikes the flange, the guide and the seat for the cope ring. Finish with a skimming coat of the same loam sifted fine. Ours: sand and clay for the loam. Not given: the loam mix, the size.
ابزارهای مورد نیاز:
قطعات ریختگی چدنی
آجر گِل پخته
ماسه
رس خام از کان
تختهٔ الواری
ماله
ابعاد نامعلوم2
2
Strike on the thickness
Strike on the thickness
When the loam is hard enough, change to the thickness sweep. Ram fine-sifted old sand at green-sand temper on by hand from the bottom up, sweeping carefully, dampen and slick it, leaving it about 1/16 in clear of the sweep, and press the flange corner sharp with the trowel. Have all the skinning loam ready first; it must be done in one pass. When it is hard, oil it all over and throw on parting sand. Ours: linseed oil.
ابزارهای مورد نیاز:
ماسه
روغن بزرک
پودر جداکننده
ماله3
3
Build the cope and gates
Build the cope and gates
Set on the cope ring and build the cope over the thickness, best with building rings and packing so it can be bound down under a cross at once. Bed plates on the sand and bind them down with the cross or binders. Put the riser at the top and enough 3/4 in runners round it, in a circle about 30 in across, to fill the mould quickly. The sand thickness stands for the metal. Not given in these pages: lifting the cope to take the thickness off before closing.
ابزارهای مورد نیاز:
آجر گِل پخته
قطعات ریختگی چدنی
ماسه
ماله4
4
Vent and pour
Vent and pour
Cut two gutters from the centre of the pit to the outside, sloping gently to the centre, and just before casting pour a little iron down to warm the air so the core gas draws off. Do not fill the trench with shavings and wood, which flash and crack the core. Fill the riser basin with soft straw or hay held down by a dry brick, so gas escapes but no rush of air damages the crown. Pour the iron through the runners. Ours: pig iron melted in a cupola.
مواد مورد نیاز این مرحله:
شمش چدن خام1 the kettleابزارهای مورد نیاز:
کاه
کوره کوپل
ملاقهٔ ریختهگریمواد
1- 1 the kettleجایگزین
مواد نقشههای متصل

10% سهم
Smelting Pig Iron in a Coke Blast Furnace — Molten Iron at Industrial Scale
توسط Elrond
فلزکاری
۶۴
۰
۰
۰
۵
۰

10% سهم
Casting Iron in a Cupola Furnace — Re-Melting Pig Iron into Finished Castings
توسط Piett
فلزکاری
۵۳
۰
۰
۰
۶
۰

10% سهم
Firing Clay Bricks in a Clamp Kiln — The Building Block of Civilization
توسط Clay
صنایع دستی
۱۶۴
۰
۰
۰
۳
۰

10% سهم
Foundry Hand Ladle: Iron Bowl, Long Shank, Clay Lining
توسط Forge
فلزکاری
۲۵
۰
۰
۰
۱
۰
این نقشه میسازد
CC0 مالکیت عمومی
این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.
با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت میکند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.
