همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۹
۰
۰
۰
۰

Top and Bottom Swages: Steel-Faced Iron Like a Fuller, Square Tang Below, Withy Handle Above, or Sprung Together (Edwinson, 1886)

Swages, the smith's top and bottom tools for bringing a weld back to round or square, from George Edwinson's smithing series in Amateur Work (1886): steel or steel-faced iron made like a fuller, the bottom tool tanged for the anvil's square hole, the top tool on a withy or iron-rod handle, or the pair coupled by a steel spring for single-handed work.
پیشرفته
A day at the forge per pair

دستورالعمل‌ها

1

Read Edwinson

"They may be made of steel throughout, or of steel-faced iron. The method of making them is similar to that for making fullers and setts."
2

Weld the blanks

As for a fuller: upset an iron bar, split it into a fork with a hot set, weld in a forged steel wedge. Or use steel throughout.

مواد مورد نیاز این مرحله:

میلهٔ آهن چکش‌خوارمیلهٔ آهن چکش‌خوار1 قطعه
فولاد بوته‌ایفولاد بوته‌ای1 قطعه
پودر بوراکسپودر بوراکس1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
پتکپتک
قلم داغقلم داغ
انبر آهنگریانبر آهنگری
3

Bottom swage

Forge the steel face into a block with a square tang that fits the square hole in the tail of the anvil, like a bottom set (his figs. 285-288).

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
4

Top swage

Forge the matching top tool with a neck for its handle.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
5

Cut the grooves

Form the working groove in each face to the section you need: round, half-round, oval, diagonal, square or rectangular. Groove sizes are ours: match the bars you forge.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
فولر (آهن شیارزن)فولر (آهن شیارزن)
سندانسندان
سوهان (سوهان دستی)سوهان (سوهان دستی)
6

Handle or spring

Give the top tool a hazel-rod or iron-rod handle as for fullers and top sets. For single-handed work, couple the top and bottom tools with a steel spring (fig. 283).

مواد مورد نیاز این مرحله:

ترکه‌های فندق (سبز، خم‌پذیر)ترکه‌های فندق (سبز، خم‌پذیر)1 قطعه
میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 قطعه
سیم آهنیسیم آهنی1 قطعه
نوار فولاد فنرنوار فولاد فنر1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
7

Grind and harden

Grind the faces level so they fit each other, then heat the whole tool and harden it (his note for hand-worked dies).

ابزارهای مورد نیاز:

سنگ چرخان تیزکنیسنگ چرخان تیزکنی
کورهٔ آهنگریکورهٔ آهنگری
سطل آب‌دهیسطل آب‌دهی
8

Use them

Work the weld at a red heat. Hold the bar and the top swage; the striker hits the top tool with a light sledge. Pass the bar to and fro, turning it for round. After each heat gauge the weld in the swage block or with callipers.

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
پتکپتک
کولیسکولیس
9

Troubleshooting

Swage troubleshooting.

Flow

Loading...
10

History and honest limits

From George Edwinson, "Smithing and Forging" XI, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 259-260 and figs. 283-290 (checked on the archive.org scan amateurworkillus06lond). The forging steps follow his fuller method (pp. 14-16). Groove sizes, the spring stock and the tools are ours.

مواد

7

ابزارهای لازم

11

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...