همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)
Forge

ایجاد شده توسط

Forge

14. نوامبر 2026NO
۱۱
۰
۰
۰
۰

Forged Centre Punches and Pin Punches: Point Hardened in Brine, Temper Run to Straw from the Stock (Griswold, Amateur Work, 1904)

Robert Gibson Griswold's first tool-making lesson in Amateur Work (Boston, 1904): four centre punches from heavy to fine and nine pin, drift, offset and riveting punches, forged from carbon tool steel, finished with file and emery, then the point alone dipped in brine and the temper let run down from the hot stock to straw yellow.
متوسط
A day for the set

دستورالعمل‌ها

1

His sizes

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Griswold

"The more work put into the steel at the working point the better will be its grade."
3

Forge the blanks

Forge carbon tool steel at no more than a bright red into the shapes of his fig. 2: a 3/8 in. chamfered head, a 2 1/2 in. body and a 1 1/2 in. taper. Heavy centre punch at least 5/8 in. across with a conical point about 3/8 in. at the base; lighter centre punches 3/8 and 1/4 in.; pin punches 1/2, 3/8 (square end), 5/16 and 1/4 in., plus parallel-ended, offset and round-ended ones.

مواد مورد نیاز این مرحله:

میلگرد فولاد ابزارمیلگرد فولاد ابزار1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
سندانسندان
چکشچکش
انبر آهنگریانبر آهنگری
4

Finish before hardening

Do all work except grinding the point now: file each punch to shape and finish it with emery cloth. Keep the striking head slightly rounded so it does not broom.

مواد مورد نیاز این مرحله:

پارچهٔ سنبادهپارچهٔ سنباده1 قطعه

ابزارهای مورد نیاز:

سوهان (سوهان دستی)سوهان (سوهان دستی)
5

Harden the point

Heat the point to a dull red and plunge only the point, about 1/2 in. (13 mm), into a brine bath.

مواد مورد نیاز این مرحله:

آب‌نمک اشباعآب‌نمک اشباع1 قطعه

ابزارهای مورد نیاز:

کورهٔ آهنگریکورهٔ آهنگری
انبر آهنگریانبر آهنگری
سطلسطل
6

Run the temper

When the point is black, rub a bright spot with emery cloth on a flat stick and watch the heat from the stock colour it. At straw yellow (460 F) plunge the whole punch in water and keep it moving. If the stock has too little heat, lay it over the furnace to draw the colour.

مواد مورد نیاز این مرحله:

آبآب1 قطعه
پارچهٔ سنبادهپارچهٔ سنباده1 قطعه

ابزارهای مورد نیاز:

سطلسطل
کورهٔ آهنگریکورهٔ آهنگری
7

Grind the points

Grind the points to shape after hardening without letting the edge turn blue; if it blues, grind back to hard metal.

ابزارهای مورد نیاز:

سنگ‌سنبادهٔ رومیزیسنگ‌سنبادهٔ رومیزی
8

Troubleshooting

Punch troubleshooting.

Flow

Loading...
9

History and honest limits

From Robert Gibson Griswold, "Tool Making for Amateurs" I, **Amateur Work** (Boston), vol. III (1903-04), pp. 273-275 and fig. 2 (checked on the archive.org scan amateurwork03bostrich). Metric figures and tools are ours.

مواد

4

ابزارهای لازم

7

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...