همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)
Tex

ایجاد شده توسط

Tex

13. نوامبر 2026FO
۵
۰
۰
۰
۰

Saddle Crupper: Slit Body, Buckled Billet and Paper-Cored Dock (Hasluck, Saddlery, 1904)

A saddle crupper runs from the back of a riding saddle to a padded loop (the dock) under the horse's tail, so the saddle cannot slide forward. This is the full-sized saddle crupper from Paul N. Hasluck's Saddlery (1904): a slit leather body, a buckled billet, and a dock shaped over string and wet brown paper. Every size is his.
متوسط
About 1 day

دستورالعمل‌ها

1

His sizes in centimetres

در حال بارگذاری دفترچهٔ Jupyter…
2

Read Saddlery, ch. V

"Full-sized saddle cruppers (Fig. 9), which are used to prevent the saddle from advancing too much, are made about 1 in. wide, and sometimes a little more."
3

Cut the body

Cut the body about 1 in wide (or a little more) and about 1 ft 6 in long. Slit one end for about 5 in and turn the other end in for a 7/8 in buckle. Shave the points of the slits and the end of the chape.

مواد مورد نیاز این مرحله:

چرم یراقچرم یراق1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
متر نواریمتر نواری
4

Make the billet and set the buckle

Cut a billet as wide as the buckle and 2 ft 4 in long; trim one end for the buckle and shave the other. Edge both pieces, polish the edges and crease them with a hot checker. Put on the buckle and stitch the billet: the first stitch by the buckle goes over the edge and through chape and billet together, the next through the loop. Run four or five stitches towards the point on each side, and come back to the buckle on the other side, making the last stitch over the side the same as the opposite side.

مواد مورد نیاز این مرحله:

چرم یراقچرم یراق1 قطعه
سگک آهنی زبانه‌دارسگک آهنی زبانه‌دار1 قطعه
نخ کتاننخ کتان1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
ابزار پخ‌زنی لبهابزار پخ‌زنی لبه
صیقل لبهٔ چرمصیقل لبهٔ چرم
ابزار تاخورابزار تاخور
مشعل پروپانمشعل پروپان
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
گیره دوخت چرمگیره دوخت چرم
5

Put on the loop

Put a loop on the flat lower down the body, about 6 in from the buckle, stitching it across at each end.

مواد مورد نیاز این مرحله:

چرم یراقچرم یراق1 قطعه
نخ کتاننخ کتان1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
قالب حلقهٔ تسمهقالب حلقهٔ تسمه
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
6

Shape the dock core

The dock is much smaller round than a gig crupper dock. Take a piece of string about 1 ft long and roll wet brown paper round it until it is the thickness you need in the middle; thin the ends by cutting the paper before damping it.

مواد مورد نیاز این مرحله:

ریسمانریسمان1 قطعه
کاغذ کادوپیچی قهوه‌ایکاغذ کادوپیچی قهوه‌ای1 قطعه

ابزارهای مورد نیاز:

قیچیقیچی
اسفنجاسفنج
متر نواریمتر نواری
7

Cover the dock

Cut the dock leather about 1 ft 1 in long; it must be soft and pliable, so damp it before stitching. Stitch it over the core as it is, without cutting a groove, drawing it very tightly over the paper. Dry the dock and finish it in shape.

مواد مورد نیاز این مرحله:

چرم یراقچرم یراق1 قطعه
نخ کتاننخ کتان1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
اسفنجاسفنج
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
گیره دوخت چرمگیره دوخت چرم
8

Join the dock and punch the billet

Stitch the dock to the slits with a splice of about 1-1/4 in. Put about a dozen holes in the billet, and vary the lengths to suit the size of horse.

مواد مورد نیاز این مرحله:

نخ کتاننخ کتان1 قطعه
موم زنبور عسلموم زنبور عسل1 قطعه

ابزارهای مورد نیاز:

کارد چرم‌بریکارد چرم‌بری
درفشدرفش
دو سوزن سراجیدو سوزن سراجی
منگنهٔ سوراخ‌کن چرممنگنهٔ سوراخ‌کن چرم
9

Troubleshooting

Saddle crupper troubleshooting.

Flow

Loading...
10

History and honest limits

From **Saddlery**, edited by Paul N. Hasluck, David McKay, 1904 (archive.org saddlery00hasl), chapter V, "Saddle Cruppers, Breastplates, and Other Accessories", saddle cruppers, pp. 40-41, Fig. 9; every fraction was read on the scan. He does not say how the billet fastens to the saddle; check against Fig. 9 and your saddle. The thread, tools and metric figures are ours.

مواد

6

ابزارهای لازم

13

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...