همکاری
هنر
زیبایی و سلامت
صنایع دستی
فرهنگ و تاریخ
سرگرمی
محیط زیست
غذا و نوشیدنی
مهندسی معکوس
علوم
ورزش
فناوری
پوشیدنی‌ها
Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)
Forge

ایجاد شده توسط

Forge

13. نوامبر 2026NO
۵
۰
۰
۰
۰

Screw-On Rubber Head Mallet: Rubber Members on Flanged Ferrules, Cupped and Cushioned on Steel Studs (Pemmerl, 1950)

Michael Pemmerl of Chatham, New Jersey, received US 2,518,059, dated 8 August 1950, for an industrial mallet with heads that change. A threaded stud stands out of each end of the steel head, and percussion members of different hardness screw on. A soft member is moulded round a hard ferrule with flanges and a threaded bore, so it cannot pull off. A steel cup holds its inner end from bulging. A thick rubber washer between cup and head stops it working loose and soaks up the shock before it reaches the hand. We make two rubber members from rubber sheet bonded round a flanged nut. The sizes are ours.
متوسط
About 2 days

دستورالعمل‌ها

1

Building a rubber member round its ferrule

در حال بارگذاری دفترچهٔ Jupyter…
2

Read US 2,518,059

"The frictional and cushioning washers 16 and 23, as interposed between the respective percussion members 14 and 17 and the mallet head 10, serve the two-fold purpose of setting up a strong frictional resistance against tendency of said percussion members to accidentally loosen or turn off the coupling studs 13 when the mallet is in use, while at the same time said washers act as impact shock absorbing means."
3

Turn the head 10

From 35 mm steel round bar turn a head 90 mm long between its end faces, and at each end a stud 13 12 mm across and 20 mm long; cut an M12 thread on each with the die. Drill a 20 mm eye through the middle, square to the axis, in a V-block, for the handle.

مواد مورد نیاز این مرحله:

میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 قطعه
روغن برشروغن برش1 قطعه

ابزارهای مورد نیاز:

تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
رندهٔ برش تراشرندهٔ برش تراش
مجموعه قلاویز و حدیدهمجموعه قلاویز و حدیده
دسته حدیدهدسته حدیده
گیرهٔ رومیزیگیرهٔ رومیزی
دریل ستونیدریل ستونی
بلوک V‌شکلبلوک V‌شکل
مجموعه متهمجموعه مته
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
عینک ایمنیعینک ایمنی
4

Ferrules 18 and cups 21-22

For each member, saw an M12 coupling nut to 30 mm and lock a 24 mm washer on it 4 mm from each end with a nut and thread locker: the flanges 19 round the threaded bore 20. Turn two cups from 45 mm bar: a base 3 mm thick with a 13 mm hole, and a skirt 12 mm deep bored 40.5 mm to embrace the member's inner end.

مواد مورد نیاز این مرحله:

مهرهٔ شش‌گوشمهرهٔ شش‌گوش6 قطعه
واشر تختواشر تخت4 قطعه
چسب قفل رزوهچسب قفل رزوه1 قطعه
میلهٔ گرد فولاد نرممیلهٔ گرد فولاد نرم1 قطعه

ابزارهای مورد نیاز:

ارهٔ آهن‌برارهٔ آهن‌بر
گیرهٔ رومیزیگیرهٔ رومیزی
آچار فرانسهآچار فرانسه
تراش فلزتراش فلز
سه‌نظام تراشسه‌نظام تراش
رندهٔ تراشکاریرندهٔ تراشکاری
میلهٔ بورینگمیلهٔ بورینگ
رندهٔ برش تراشرندهٔ برش تراش
کولیس دیجیتال ۶ اینچیکولیس دیجیتال ۶ اینچی
5

Build the rubber members 17

Scribe and cut 4 mm rubber discs 40 mm across with the knife: for each member, seven holed to the ferrule (24 mm holes level with the two flanges and 22 mm round the nut, so the discs either side trap each flange's rim) and five solid discs for the striking face. Brush contact cement on both faces, let it go touch-dry, and build the member up over its ferrule, the ferrule's end flush with the member's inner end; press it in clamps overnight and trim it round.

مواد مورد نیاز این مرحله:

ورق لاستیک طبیعیورق لاستیک طبیعی1 قطعه
چسب تماسیچسب تماسی1 قطعه

ابزارهای مورد نیاز:

قطب‌نماقطب‌نما
چاقوی کاردستیچاقوی کاردستی
گیرهٔ میله‌ایگیرهٔ میله‌ای
6

Handle and assembly

Turn an ash handle 300 mm long, fit it in the eye with a glued wedge. Cut two 6 mm rubber washers 23, 40 mm across with 13 mm holes. On each stud put a rubber washer, then a cup, skirt outwards, then screw a member on until its end is in the cup and the washer is squeezed; it should take a firm twist to undo.

مواد مورد نیاز این مرحله:

تختهٔ چوب سختتختهٔ چوب سخت1 قطعه
چسب چوبچسب چوب1 قطعه
ورق لاستیک طبیعیورق لاستیک طبیعی1 قطعه

ابزارهای مورد نیاز:

تراش چوبتراش چوب
ست ابزار تراش (HSS)ست ابزار تراش (HSS)
ارهٔ آهن‌برارهٔ آهن‌بر
چکش گِرد‌سرچکش گِرد‌سر
چاقوی کاردستیچاقوی کاردستی
7

Troubleshooting

Interchangeable-head mallet troubleshooting.

Flow

Loading...
8

History and honest limits

**Michael Pemmerl** of Chatham, New Jersey, US 2,518,059, dated 8 August 1950, filed 31 October 1947. He claimed a mallet head with a screw-threaded coupling stud at an end, "a percussion member made of relatively soft material such as lead, an internally screw-threaded ferrule made of hard metal imbedded in said percussion member, said ferrule having external annular flanges", "a perforate cupped reenforcing member", and "a perforate rubber washer of substantial thickness" between cup and head. His soft members were moulded, and he names rubber among their materials; ours are rubber discs bonded round the ferrule. He also shows hard metal and rawhide members. He gives no sizes; every size here is ours.

مواد

9

ابزارهای لازم

21

این نقشه می‌سازد

CC0 مالکیت عمومی

این نقشه تحت مجوز CC0 منتشر شده است. شما آزاد هستید آن را کپی، ویرایش، توزیع و برای هر هدفی بدون نیاز به اجازه استفاده کنید.

با خرید محصولات از طریق نقشه از سازنده حمایت کنید و او کمیسیون سازنده تعیین شده توسط فروشندگان، دریافت می‌کند یا یک نسخه جدید از این نقشه ایجاد کنید و آن را به عنوان اتصال در نقشه خود قرار دهید تا درآمد به اشتراک گذاشته شود.

بحث و گفتگو

(0)

ورود برای شرکت در بحث

در حال بارگذاری نظرات...