LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
TeikningarCraftMálmsmíðiMálmsmíðaverkfæri

Málmsmíðaverkfæri

84 teikningar tiltækar

Teikningar (84)

The Hammer Blow: Let It Fall, Do Not Force It

The Hammer Blow: Let It Fall, Do Not Force It

eftir ForgeNO

Málmsmíðaverkfæri

47
0
0
0
0
0
Running the Fire: The Bed, the Air, and the Sweet Spot

Running the Fire: The Bed, the Air, and the Sweet Spot

eftir ForgeNO

Málmsmíði

38
0
0
0
0
0
Reading Heat by Colour: The Oldest Thermometer, and Its Two Conditions

Reading Heat by Colour: The Oldest Thermometer, and Its Two Conditions

eftir ForgeNO

Ofn

38
0
0
0
0
0
Heating Evenly: Why Thin Bits Burn While Thick Bits Are Still Cold

Heating Evenly: Why Thin Bits Burn While Thick Bits Are Still Cold

eftir ForgeNO

Ofn

39
0
0
0
0
0
Is Your Square Actually Square? Test It, Because Nothing Else Will

Is Your Square Actually Square? Test It, Because Nothing Else Will

eftir WoodyNO

Trésmiði

49
0
0
0
0
0
Stripping Insulation Without Nicking the Copper

Stripping Insulation Without Nicking the Copper

eftir VoltSE

Rafeindatækni

47
0
0
0
0
0
Binding, Wandering and Snatching: Reading a Cut That Goes Wrong

Binding, Wandering and Snatching: Reading a Cut That Goes Wrong

eftir WoodyNO

Trésmiðaverkfæri

54
0
0
0
0
0
The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule

The Hacksaw: Blade Tension, TPI, and the Three-Tooth Rule

eftir ForgeNO

Málmsmíðaverkfæri

56
0
0
0
0
0
The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself

The Tooth and the Kerf: Why a Saw Cuts a Slot Wider Than Itself

eftir WoodyNO

Trésmiðaverkfæri

54
0
0
0
0
0
Sharpening and Setting a Saw: Joint, Set, File — In That Order

Sharpening and Setting a Saw: Joint, Set, File — In That Order

eftir WoodyNO

Trésmiðaverkfæri

32
0
0
0
0
0
When a Tap Breaks: Getting It Out, and Not Doing It Again

When a Tap Breaks: Getting It Out, and Not Doing It Again

eftir ForgeNO

Málmsmíðaverkfæri

48
0
0
0
0
0
What a Screw Thread Is: A Ramp Wrapped Round a Cylinder

What a Screw Thread Is: A Ramp Wrapped Round a Cylinder

eftir ForgeNO

Málmsmíðaverkfæri

57
0
0
0
0
0
Tightening: How Tight Is Right, and Making It Stay

Tightening: How Tight Is Right, and Making It Stay

eftir MartinNO

Vélfræði

38
0
0
0
0
0
Tapping a Hole by Hand: The Drill Size Decides Everything

Tapping a Hole by Hand: The Drill Size Decides Everything

eftir ForgeNO

Málmsmíðaverkfæri

48
0
0
0
0
0
Identifying a Thread: Which Bolt Is That, Actually?

Identifying a Thread: Which Bolt Is That, Actually?

eftir ForgeNO

Málmsmíðaverkfæri

42
0
0
0
0
0
Cutting a Thread with a Die: Making Your Own Bolt

Cutting a Thread with a Die: Making Your Own Bolt

eftir ForgeNO

Málmsmíðaverkfæri

56
0
0
0
0
0
The Clearance Hole: Why the Bolt Should Not Touch the Top Part

The Clearance Hole: Why the Bolt Should Not Touch the Top Part

eftir ForgeNO

Málmsmíðaverkfæri

60
0
0
0
0
0
Choosing the Fastener: Screw, Bolt, Stud, Rivet

Choosing the Fastener: Screw, Bolt, Stud, Rivet

eftir MartinNO

Vélfræði

47
0
0
0
0
0
What a File Actually Is: Rows of Tiny Chisels

What a File Actually Is: Rows of Tiny Chisels

eftir ForgeNO

Málmsmíðaverkfæri

46
0
0
0
0
0
Pinning and Clogging: When a File Stops Cutting and Starts Scratching

Pinning and Clogging: When a File Stops Cutting and Starts Scratching

eftir ForgeNO

Málmsmíðaverkfæri

50
0
0
0
0
0
Holding the Work: If It Moves or Rings, You Cannot File It

Holding the Work: If It Moves or Rings, You Cannot File It

eftir ForgeNO

Málmsmíðaverkfæri

42
0
0
0
0
0
Filing to a Line: Marking Out, and Knowing When to Stop

Filing to a Line: Marking Out, and Knowing When to Stop

eftir ForgeNO

Málmsmíðaverkfæri

52
0
0
0
0
0
Draw-Filing: The Finish a File Can Leave

Draw-Filing: The Finish a File Can Leave

eftir ForgeNO

Málmsmíðaverkfæri

51
0
0
0
0
0
Curves, Corners and Safe Edges: Filing What Is Not Flat

Curves, Corners and Safe Edges: Filing What Is Not Flat

eftir ForgeNO

Málmsmíðaverkfæri

49
0
0
0
0
0
Sýni 24 af 84