LIST
FEGURÐ OG VELLÍÐAN
HANDVERK
MENNING OG SAGA
SKEMMTUN
UMHVERFI
MATUR OG DRYKKUR
ÖFUGVERKFRÆÐI
VÍSINDI
ÍÞRÓTTIR
TÆKNI
KLÆÐANLEG TÆKNI
Spiral-Vane Spring-Agitator Churn: Vanes That Snap Springs on the Bottom
Watson wanted "the lower stratum of the cream" kept "in brisk motion" while a dasher lifted the rest.
Peter H. Watson of Rockford, Illinois, assignor to Nathaniel S. Wheeler of Painesville, Ohio, received US 5,573, dated 16 May 1848, for a churn with a rotary spiral dasher — flat vanes fixed between arms ninety degrees apart, so they twist into spirals — over "elastic vibrating agitators": a removable cross on the bottom carrying curved springs that the vanes press down and release. A tube in the lid lets air in and a tube in the side lets it out, kept circulating by the dasher. He set the churn obliquely on a frame to turn the winch.
This rung counts the springs' snaps, then prints the vane spiders and the spring cross, twists flat vanes between them, and makes butter.
Lengra kominn
About 5 hours, plus printing
Leiðbeiningar
1
1
Springs and vanes
Springs and vanes
Hleð Jupyter-vinnubók…
2
2
A spiral that lifts the cream before it
A spiral that lifts the cream before it
The embedded blueprint lifts cream with an Archimedean screw in a tube. Watson's twisted vanes lift it in the open churn and let it fall through the air.
3
3
Read US 5,573
Read US 5,573
"On the upper side of these arms a series of curved elastic pieces of wood or metal are secured by one end, the end projecting from the arm at right angles or nearly so and inclining upward; as the vanes of the dasher revolve in the direction indicated by the arrows Figs. 2 and 3 they depress the springs f f f in its passing over them, but the moment the vane has turned far enough to release the spring the latter flies up again to its former position."
4
4
Print the parts
Print the parts
Print two vane spiders, the agitator cross with its twelve tongues and the crank arm. Print the cross in PETG if you have it: its thin tongues must flex and spring back. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Efni fyrir þetta skref:
PETG-þráður1 stykkiNauðsynleg verkfæri:
FDM-þrívíddarprentari5
5
Print the spider
6
6
Print the agitator
7
7
Print the crank arm
8
8
Twist the vanes
Twist the vanes
Glue the spiders on a 10 mm square hardwood shaft 110 mm apart, the upper turned 90° to the lower. Cut four strips of thin stainless sheet about 60 × 130 mm, deburr them, and seat each in a lower spider's slot and the next upper slot round, so it twists a quarter turn into a spiral, as his did. Glue them in.
Efni fyrir þetta skref:
Harðviðartappar1 stykki
Plata úr ryðfríu stáli - 3041 stykki
Tveggja þátta epoxý1 stykkiNauðsynleg verkfæri:
Plötuklippur
Gratáhald
Þvingur9
9
The tub
The tub
Set the agitator cross on the floor of a food-grade bucket, the shaft's foot through its centre hole into a drilled seat. Drill the lid at the centre for the shaft, and fit a short tube in the lid and another near the top of the side for the air. Glue the crank arm and a dowel handle on the shaft. Prop the bucket at an angle on a pine frame for cranking.
Efni fyrir þetta skref:
20 lítra fata1 stykki
Furuborð1 stykki
Tréskrúfa #8 x 1"1 stykki
Trélím1 stykkiNauðsynleg verkfæri:
Hleðslubor
Borasett
Handsög
Skrúfjárnasett10
10
The patent drawing
The patent drawing
US 5,573 drawing sheet, public domain (expired patent).
11
11
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 1.5 litres. Crank the way the springs incline, so the vanes press them down and let them fly up; time until the butter comes. Lift out the cross to gather the butter with the dasher alone, as he allowed. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Efni fyrir þetta skref:
Rjómi1500 ml
Gróft sjávarsalt1 stykki
Vatn1 stykkiNauðsynleg verkfæri:
Hitamælir með nema sem situr í
Skeiðklukka
Stafræn eldhúsvog
Stór hrærskál úr ryðfríu stáli12
12
Springs that break, vanes that jam
Springs that break, vanes that jam
Spiral-vane spring-agitator churn troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Peter H. Watson** of Rockford, Winnebago County, Illinois, received US 5,573, dated 16 May 1848, assigned to Nathaniel S. Wheeler of Painesville, Ohio. The dasher had eight horizontal arms; each vane could be "one broad piece or of several narrow pieces"; the agitators could be removed once the butter was separated. He claimed "the combination of the elastic vibrating agitator with the rotary spiral dasher."
**Honest limits.** A bucket, printed spiders and a printed spring cross stand in for his tub and wooden or metal springs; our dasher has four vanes on two spiders. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Efni
11- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
- 1500 mlStaðgengill
- 1 stykkiStaðgengill
- 1 stykkiStaðgengill
Nauðsynleg verkfæri
12- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Hleðslubor3% þóknunMagento Legacy Storeships internationallyStaðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
- Staðgengill
Hönnunarskrár
3Þessi teikning býr til
Tengd Blueprint
Þessi blueprint deila þekkingu — tækni, efni eða meginreglur
Screw-Lift Churn: An Archimedean Screw Keeps the Whole Body of Cream Moving
eftir Emma
MATUR OG DRYKKUR
24
0
0
0
0
0
Rotary Stirring Churn: Three Floats That Stop the Cream Merely Going Round
eftir YourGrandma
MATUR OG DRYKKUR
32
0
0
0
0
0
Draw-and-Throw Rotary Churn: Cream Drawn In at the End, Thrown Against Breakers
eftir TheChef
MATUR OG DRYKKUR
29
0
0
0
0
0
CC0 opinbert ríki
Þessi teikning er gefin út undir CC0. Þér er frjálst að afrita, breyta, dreifa og nota þetta verk í hvaða tilgangi sem er, án þess að biðja um leyfi.
Studdu smiðinn með því að kaupa vörur í gegnum teikningu hans þar sem hann fær þóknun smiða sem seljendur ákvarða, eða búðu til nýja endurskoðun á þessari teikningu og tengdu hana sem tengingu í þinni eigin teikningu til að deila tekjum.