ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Bell-Crank Vibrating Beater Churn: Beaters Rocked on Hung Fulcrums by a Cranked Shaft
Rhodes improved "the common churn" by the way he worked and hung its beaters.
Clarkson Rhodes of Morrow, Ohio, received US 8,959, dated 18 May 1852, for a churn box whose top has a convex recess for the cranks to pass, ventilated by a perforated tin plate over a hole "some 3/4 or an inch in diameter." A shaft bent into a double bell crank turns across the top; rods from the shaft carry the fulcrum on which the beaters vibrate, and rods from the cranks give them "an alternate up and down motion." The internal work lifts out with the top for cleaning.
This rung works out the beaters' swing, then prints the beaters and fulcrum hangers, bends the cranked shaft, and makes butter.
Intermedio
About 4 hours, plus printing
Istruzioni
1
1
The beaters' swing
The beaters' swing
Caricamento del notebook Jupyter…
2
2
A double crank working the beaters before it
A double crank working the beaters before it
The embedded blueprint swings an upright dasher from a double crank. Rhodes rocks beaters on fulcrums hung from the cranked shaft itself.
3
3
Read US 8,959
Read US 8,959
"The shaft 1, 1, is turned by crank c, of which works the cranks 5, 5, and rods 3, 3, 3, 3 which gives the beaters or dashers 4, 4, 4, 4, an alternate up and down motion, and thereby causing an effectual churning of the milk."
4
4
Print the parts
Print the parts
Print four beaters (/uploads/blueprints/bell-crank-vibrating-beater-churn-beater.stl) and two fulcrum hangers (/uploads/blueprints/bell-crank-vibrating-beater-churn-fulcrum-hanger.stl). Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
Materiali per questo passaggio:
Filamento PETG1 pezzoStrumenti necessari:
Stampante 3D a filamento (FDM)5
5
The cranked shaft
The cranked shaft
Bend a 6 mm steel rod into a shaft with two cranks of about 25 mm throw, pointing opposite ways, and a handle at one end. Lay it in notches in the ends of a food-safe box about 230 × 150 × 200 mm, under a plywood lid with a raised recess for the cranks and a small hole covered with perforated stainless sheet for air.
Materiali per questo passaggio:
Tondo di acciaio dolce1 pezzo
Contenitore di conservazione per uso alimentare1 pezzo
Pannello di compensato1 pezzo
Lamiera di acciaio inossidabile - 3041 pezzoStrumenti necessari:
Chiave regolabile a rullino
Seghetto per metalli
Sega da traforo
Cesoie da lattoniere6
6
Hang the beaters
Hang the beaters
Hang each fulcrum hanger from the shaft beside a crank, on a loop of steel wire, and pin two beaters crossed on each hanger's lower hole. Join each beater's end to the nearer crank with a wire rod, eyes at both ends.
Materiali per questo passaggio:
Filo di acciaio armonico1 pezzo
Viti da metallo1 pezzo
Dado esagonale1 pezzoStrumenti necessari:
Chiave regolabile a rullino
Set di cacciaviti7
7
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the box with one side off to show the cranked shaft across the top, the rods hanging to the fulcrums, the crossed beaters and the crank rods.
8
8
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres. Fit the lid and turn the handle steadily; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
Materiali per questo passaggio:
Panna da montare2000 ml
Sale marino grosso1 pezzo
Acqua1 pezzoStrumenti necessari:
Termometro a sonda permanente
Cronometro
Bilancia digitale da cucina
Grande ciotola da impasto in acciaio inossidabile9
9
Beaters that jam, rods that bend
Beaters that jam, rods that bend
Bell-crank beater troubleshooting.
Flow
Loading...
10
10
History and honest limits
History and honest limits
**Clarkson Rhodes** of Morrow, Warren County, Ohio, received US 8,959, dated 18 May 1852 (the drawing sheet is lettered "G. Rhodes"; the specification gives Clarkson). He did not confine himself to the number or form of the dashers. He claimed the beaters hung by rods from the shaft on a fulcrum and worked by the rods and bell cranks.
**Honest limits.** A food-safe box, steel rod and printed beaters stand in for his. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
Materiali
11- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- Segnaposto
- 1 pezzoSegnaposto
- Segnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
- 2000 mlSegnaposto
- 1 pezzoSegnaposto
- 1 pezzoSegnaposto
Strumenti richiesti
10- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
- Segnaposto
File di progetto
1Questo progetto realizza
Blueprint correlati
Questi blueprint condividono conoscenze — tecniche, materiali o principi
Oscillating Paddle Churn: Oblique Paddles Swung to and Fro by a Strap
di Martin
CIBO E BEVANDE
33
0
0
0
0
0
Spring-Wire Twin Dash Churn: Two Hinged Dashes Rocked by a Sprung Wire on a Crank
di YourGrandma
CIBO E BEVANDE
34
0
0
0
0
0
Interraking Plunger Churn: Two Rakes Worked Oppositely by a Double Crank
di Martin
CIBO E BEVANDE
23
0
0
0
0
0
CC0 Pubblico dominio
Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.
Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.