ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
FUTURO VERDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Building an Infrared Distance Sensor
Ed

Creato da

Ed

13. luglio 2026FI
0
0
0
0
0

Building an Infrared Distance Sensor

Measure distance with light. A Sharp infrared sensor bounces a beam off an object and reports, as a voltage, the angle it returns at — closer objects give a higher reading. The Arduino turns that into an approximate distance and lights an LED when something comes near: a touchless switch, a hand-wave trigger, or a robot's eyes. Unlike the ultrasonic sensor, this uses infrared light, works at short range, and makes no sound.

Intermedio
1 hour

Istruzioni

1

Wire the sensor and LED

The Sharp sensor has a 3-wire cable: VCC (red) to Arduino 5V, GND (black) to GND, and signal (white or yellow) to A0. On the breadboard, wire an LED from pin 7 through a 330 Ω resistor to GND (long leg to the pin).

Materiali per questo passaggio:

Arduino Uno R3Arduino Uno R31 pezzo
Infrared Proximity Sensor - Sharp GP2Y0A21YKInfrared Proximity Sensor - Sharp GP2Y0A21YK1 pezzo
LED - Basic 5mmLED - Basic 5mm1 pezzo
Resistor 330 Ohm 1/6 Watt PTH - 20 packResistor 330 Ohm 1/6 Watt PTH - 20 pack1 confezione
BreadboardBreadboard1 pezzo
Jumper Wires (Male-to-Male)Jumper Wires (Male-to-Male)1 confezione
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port.

Materiali per questo passaggio:

USB-B CableUSB-B Cable1 pezzo

Strumenti necessari:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the distance sketch

Paste this sketch and upload, then open the Serial Monitor. It reads the sensor, estimates the distance, and lights the LED when something is within 20 cm.

ir_distance_sensor.inoarduino
// Sharp GP2Y0A21YK infrared distance sensor (valid ~10-80 cm).
// The output is NON-LINEAR (roughly 1/distance); the formula below is a common
// approximation - calibrate against known distances if you need accuracy.
// Sensor signal on A0; indicator LED on pin 7.

const int IR_PIN = A0;
const int LED_PIN = 7;
const int NEAR_CM = 20;   // light the LED when something is closer than this

void setup() {
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);
}

void loop() {
  int raw = analogRead(IR_PIN);
  float volts = raw * (5.0 / 1023.0);

  // approximate distance in cm for the GP2Y0A21 curve
  float distance = 27.86 * pow(volts, -1.15);

  Serial.print(distance);
  Serial.println(" cm");

  if (distance < NEAR_CM) {
    digitalWrite(LED_PIN, HIGH);   // object nearby
  } else {
    digitalWrite(LED_PIN, LOW);
  }
  delay(200);
}
4

Test and understand the curve

Open the Serial Monitor and move your hand between about 10 and 80 cm — the printed distance should track it, and the LED lights inside 20 cm. Two things to know: below ~10 cm the reading becomes ambiguous (the sensor's curve folds back), and the output is non-linear, so for real accuracy note the raw value at a few known distances and fit your own curve.

5

Put it to work

Use it as a touchless switch (wave to trigger), a shelf or drawer 'is-it-open' sensor, or an obstacle detector for a small robot. Change NEAR_CM to set the trigger distance, or swap in the short-range (4–30 cm) or long-range (20–150 cm) Sharp sensor for a different span.

Materiali

7

Strumenti richiesti

1
Totale stimato
€57.00

Blueprint correlati

Questi blueprint condividono conoscenze — tecniche, materiali o principi

Building an Ultrasonic Parking Sensordi Ed
Blinking LED — Your First Arduino Projectdi Admiral OOM

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Building an Ultrasonic Parking Sensorelectronics
Building an Air-Quality Monitorelectronics
Building a Carbon Monoxide Detectorelectronics
Building a Methane Gas Leak Detectorelectronics
Controlling a Stepper Motor with an EasyDriverelectronics
Using an LCD — SIK Circuit 15electronics

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...