Collaborazione
ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Making a Color-Changing LilyPad Patch
Ed

Creato da

Ed

13. luglio 2026FI
45
0
0
0
0

Making a Color-Changing LilyPad Patch

Sew a patch that glows in any color. A single RGB LED holds red, green and blue elements; by fading each one with the microcontroller's PWM pins you mix millions of colors and cycle through the rainbow. The e-textile version of the classic RGB colour-mixing project.

Intermedio
1-2 hours

Istruzioni

1

Sew the board and RGB LED

Sew a LilyPad Arduino onto felt. The RGB LED has four legs — bend each into a small loop so it can be sewn. Wire the common cathode (the longest leg) to -, and the red, green and blue legs to pins 5, 6 and 9. Keep the four lines from touching each other.

Materiali per questo passaggio:

LilyPad Arduino Simple BoardLilyPad Arduino Simple Board1 pezzo
LED - RGB Diffused Common Cathode - 5mmLED - RGB Diffused Common Cathode - 5mm1 pezzo
Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 rocchetto
Foglio di feltro di lanaFoglio di feltro di lana1 foglio

Strumenti necessari:

Aghi da cucito a manoAghi da cucito a mano
2

Connect the programmer

Plug the LilyPad FTDI onto the programming header and connect the USB cable. Open the Arduino IDE and select the LilyPad Arduino board and its serial port.

Strumenti necessari:

Computer con l'IDE ArduinoComputer con l'IDE Arduino
LilyPad FTDI Basic Breakout - 5VLilyPad FTDI Basic Breakout - 5V
Cavo USB-BCavo USB-B
3

Upload the color-mixing sketch

Paste this sketch and upload. It fades the LED through red, green, blue and the mixes using analogWrite (PWM).

lilypad_color_changing.inoarduino
// Mix colors on a common-cathode RGB LED.
// Red/Green/Blue legs on PWM pins 5, 6, 9; common cathode to - (GND).

const int RED_PIN = 5;
const int GREEN_PIN = 6;
const int BLUE_PIN = 9;

void setColor(int r, int g, int b) {
  analogWrite(RED_PIN, r);     // 0 = off, 255 = full
  analogWrite(GREEN_PIN, g);
  analogWrite(BLUE_PIN, b);
}

void setup() {
  pinMode(RED_PIN, OUTPUT);
  pinMode(GREEN_PIN, OUTPUT);
  pinMode(BLUE_PIN, OUTPUT);
}

void loop() {
  setColor(255, 0, 0);   delay(500);  // red
  setColor(0, 255, 0);   delay(500);  // green
  setColor(0, 0, 255);   delay(500);  // blue
  setColor(255, 255, 0); delay(500);  // yellow
  setColor(0, 255, 255); delay(500);  // cyan
  setColor(255, 0, 255); delay(500);  // magenta
  setColor(255, 255, 255); delay(500);// white
}
4

Watch it cycle, then mix your own

The LED fades through the colors on its own. Make your own by changing the three numbers in setColor(red, green, blue) — each 0–255. Note: at the LilyPad's lower voltage blue and green look a little dimmer than red, which is normal for RGB LEDs.

5

Go wireless and wear it

Plug a 3.7 V LiPo into the LilyPad Arduino's JST connector and switch on — the higher voltage also makes the colors brighter. Sew the felt onto a bag or costume for a colour-changing glow.

Materiali per questo passaggio:

LiPo Battery 3.7V 1000mAh (JST Connector)LiPo Battery 3.7V 1000mAh (JST Connector)1 pezzo

Materiali

5

Strumenti richiesti

4
Totale stimato
Ciò che il maker ha acquistato. I materiali senza prezzo si trovano dove li compri tu.
€78.32

Blueprint correlati

Questi blueprint condividono conoscenze — tecniche, materiali o principi

Blinking an LED with LilyPad Arduino

Blinking an LED with LilyPad Arduino

di EdFI

Digitale

43
0
0
0
0
0
Driving an RGB LED — SIK Circuit 3

Driving an RGB LED — SIK Circuit 3

di EdFI

Digitale

100
0
0
0
0
0

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...