ARTE
BELLEZZA E BENESSERE
MESTIERE
CULTURA E STORIA
DIVERTIMENTO
AMBIENTE
CIBO E BEVANDE
INGEGNERIA INVERSA
SCIENZE
SPORT
TECNOLOGIA
INDOSSABILI
Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads
Woody

Creato da

Woody

14. ottobre 2026NO
15
0
0
0
0

Wooden Barrel: Bulged Oak Staves Bent by Fire, with Two Heads

A barrel is the cooper's closed vessel: oak staves held by hoops, bulging at the middle, with flat heads set in grooves at both ends. Coopers heat the staves to bend them. Shape staves wider at the middle than the ends, raise them in a hoop, heat them over a small fire and draw the open end together, drive the hoops, and fit the heads. The picture: a new oak barrel in a cooper's workshop, with iron hoops on the floor.
Avanzato
Several days

Istruzioni

1

Shape the staves

Rive and shave oak staves as for the vat, but taper each from the middle toward both ends, and hollow the inside face a little.

Materiali per questo passaggio:

Tavola di legno duroTavola di legno duro8 pezzi

Strumenti necessari:

Coltello da spacco (froe)Coltello da spacco (froe)
Banco da pettoBanco da petto
Coltello a due maniciColtello a due manici
Pialla a manoPialla a mano
2

Raise and fire

Stand the staves inside one hoop to form a skirt. Light a small charcoal fire inside, wet the outside, and as the staves warm, draw the open end together with a rope round it until a hoop can be driven on.

Materiali per questo passaggio:

Carbone di legnaCarbone di legna3 as required
AcquaAcqua10 litri

Strumenti necessari:

Cerchio di ferroCerchio di ferro
Cordame robustoCordame robusto
Martello a penna trasversaleMartello a penna trasversale
Guanti resistenti al caloreGuanti resistenti al calore
3

Hoops

Drive the rest of the iron hoops on, two near each end and two at the quarters, until the joints close tight.

Materiali per questo passaggio:

Cerchio di ferroCerchio di ferro6 pezzi

Strumenti necessari:

Martello a penna trasversaleMartello a penna trasversale
4

Ends and grooves

Level the ends and bevel the inside edge with the adze, then cut a groove round the inside near each end.

Strumenti necessari:

Ascia a sgorbiaAscia a sgorbia
Serie di scalpelliSerie di scalpelli
5

Heads and bung

Join planks into two boards, scribe circles to fit the grooves, cut and bevel them, slack the end hoops and spring the heads in. Bore a bung hole in the middle stave. Fill with water to swell it tight.

Materiali per questo passaggio:

Tavola di legno duroTavola di legno duro2 pezzi
AcquaAcqua50 litri

Strumenti necessari:

Compasso a punte fisseCompasso a punte fisse
Sega a manoSega a mano
Pialla a manoPialla a mano
Martello a penna trasversaleMartello a penna trasversale
Trapano a manoTrapano a mano
6

Capacity of a barrel

Caricamento del notebook Jupyter…

Materiali

4

Strumenti richiesti

13

Questo progetto realizza

CC0 Pubblico dominio

Questo progetto è rilasciato sotto CC0. Sei libero di copiare, modificare, distribuire e utilizzare quest'opera per qualsiasi scopo, senza chiedere permesso.

Supporta il Maker acquistando prodotti tramite il suo progetto dove guadagna una Commissione Maker stabilita dai venditori, oppure crea una nuova iterazione di questo progetto e includilo come collegamento nel tuo progetto per condividere i ricavi.

Commenti

(0)

Accedi per partecipare alla discussione

Caricamento commenti...