コラボレーション
アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)
Volt

作成者

Volt

4. 11月 2026SE
17
0
0
0
0

Electric Arc Furnace: the Héroult Series-Arc Steel Furnace (Stansfield, 1914)

Héroult's steel furnace: a tilting hearth like an open-hearth furnace, lined with dolomite, with two carbon electrodes coming down through the roof. The current goes down one electrode, arcs into the slag, passes through the molten steel and arcs back up the other, so the heat goes straight into the metal. Result: an electric steel furnace about 7 x 4 ft inside for a 3 ton charge, run at about 350 kW and 110 V. Source: A. Stansfield, The Electric Furnace, 2nd ed. (1914), pp. 115-116, 214-216. Unknown: case and tilting gear details, electrode size. Picture: a drawn diagram (Fig. 93 is blank in the scan).
エキスパート
Unknown

手順

1

Build the case and lining

Build the furnace in a steel case on a tilting mounting, about 7 x 4 ft inside, with charging doors at the ends. Line it with dolomite bricks and crushed dolomite; dolomite or magnesite on the hearth, which allows strongly basic slags. Ours: mild steel plate. Not given: the case and tilting gear, the bricks' making.

このステップの材料:

軟鋼板軟鋼板1 case
ドロマイト(マグネシア質石灰岩)ドロマイト(マグネシア質石灰岩)1 lining and crushed dolomite
マグネサイトブロックマグネサイトブロック1 hearth, if magnesite

必要な工具:

アーク溶接機アーク溶接機
左官ごて左官ごて
不明な寸法不明な寸法
2

Make the removable roof

Make the roof of silica brick, covered with steel plates and given eyes so it can be lifted off. Between the two electrode holes use bronze plates instead of steel, because steel there would raise the inductance of the AC circuit. Fit water jackets round each electrode hole for a close fit, so less heat escapes and the electrodes do not burn in the air. Ours: copper tube for the water jackets. Silica brick has no head here.

このステップの材料:

不明な材料不明な材料1 silica brick
軟鋼板軟鋼板1 roof plates
青銅板青銅板1 plates between electrodes
銅管銅管1 water jackets

必要な工具:

アーク溶接機アーク溶接機
ボール盤ボール盤
水水
3

Hang the electrodes

Use two vertical carbon electrodes, square in section. Carry each in a holder on an arm supported by the furnace itself, so its height does not change when the furnace tilts: four contact pieces round the electrode, drawn tight by a steel strap and a screw in the arm, with the cable bolted to them. Raise and lower each electrode separately, by a regulator controlled by the voltage between it and the metal. Not given: electrode size, the regulator's build.

このステップの材料:

炭素電極炭素電極2 electrodes
不明な金属不明な金属1 holders, arms, contact pieces

必要な工具:

ボール盤ボール盤
4

Melt and refine a charge

Charge steel scrap with some iron ore and lime. Keep each electrode a little above the slag, leaving room for its arc. Regulate the current by hand while the scrap melts, then switch to automatic; full power only after about an hour. Pour off the slag and make a second, then a third, with lime and a little sand and fluorspar, before the final additions. At La Praz this took about 350 kW at 110 V: 5 hours for 1.25 tons of low-carbon steel, 8 hours for 2.33 tons of high-carbon steel. Not given: the electric supply.

必要な工具:

水水

材料

8

必要な工具

5

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...