アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
グリーンフューチャー
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Consolidating an Iron Bloom — Hammering Sponge Iron into Wrought Iron
Forge

作成者

Forge

26. 5月 2026NO
18
0
0
10
0

Consolidating an Iron Bloom — Hammering Sponge Iron into Wrought Iron

The bloomery furnace does not produce liquid iron — it produces a bloom: a spongy, porous mass of iron mixed with slag, charcoal fragments, and voids. This raw bloom is useless as a material until it is consolidated — repeatedly heated to welding temperature and hammered to squeeze out the slag and compact the iron into a dense, workable billet.

This is the critical step between smelting and smithing. Without consolidation, there are no iron tools. The process requires intense physical effort — the bloom must be worked at bright yellow heat (over 1,100 °C) while the slag is still liquid enough to be expelled by hammer blows. Each fold and weld refines the iron further, aligning the grain and removing impurities.

A single bloom from a small bloomery yields about 1-2 kg of consolidated wrought iron after losing 30-50% of its mass to expelled slag. This billet is the raw stock for every iron tool, weapon, and fastener.

上級者
2-4 hours

手順

1

Extract the bloom from the furnace

After the bloomery smelt is complete, break open the furnace wall or rake out the bloom from the tap hole using long iron tongs. The bloom emerges as a rough, irregular mass about the size of a large fist, glowing dull red, with visible slag pockets and charcoal fragments embedded in the surface. Handle quickly — it loses heat rapidly.

必要な工具:

Long-Handled TongsLong-Handled Tongs
2

First compaction while still hot

Immediately place the hot bloom on a flat stone anvil and strike it firmly with a heavy hammerstone or iron sledge. The goal is not shaping — it is compaction. Each blow squeezes liquid slag out through the pores. Slag runs out as glowing orange streams. Hit from all sides, rotating the bloom between blows. Work fast before the bloom cools below working temperature.

必要な工具:

HammerstoneHammerstone
Flat Stone SlabFlat Stone Slab
3

Reheat in the forge

Place the partially compacted bloom back into a charcoal forge fire. Work the bellows to raise the temperature to bright yellow-white heat — at least 1,100 °C, ideally 1,250 °C. At this temperature the remaining slag melts and can be expelled. The iron itself does not melt (iron melts at 1,538 °C) but becomes soft enough to weld to itself when hammered.

このステップの材料:

CharcoalCharcoal5 kg
4

Hammer at welding heat

Remove the bloom from the forge at bright yellow-white heat. Strike it with heavy, deliberate blows on the anvil. At this temperature the iron grains weld together on contact under hammer pressure — this is forge welding, the fundamental joining technique of pre-industrial metalwork. Slag sprays out as sparks with each blow. Continue until the bloom flattens into a rough rectangular shape.
5

Cut, fold, and re-weld

Using a hot chisel or the edge of the anvil, cut the flattened bloom nearly in half. Fold one half over the other and reheat to welding temperature. Hammer the two layers together until they fuse completely. This folding redistributes the remaining slag into thinner and thinner layers, and begins to align the iron grain structure. Repeat the fold-and-weld cycle 3-5 times.
6

Draw out into a billet

After the final weld, hammer the consolidated iron into a bar shape — roughly 20-30 cm long, 3-4 cm wide, and 2 cm thick. This is the billet or bar stock from which tools will be forged. Work with even, overlapping blows to produce a uniform cross-section. The surface should now show clean iron with minimal slag inclusions.
7

Test the wrought iron quality

Let the billet cool completely. Examine the surface — good wrought iron has a fibrous texture visible when the surface is filed, similar to wood grain. This fibrous structure gives wrought iron its characteristic toughness. Nick the edge with a chisel and bend: it should deform without snapping. Brittle iron or iron with large slag inclusions needs more folding and welding.

材料

1

必要な工具

3

接続ブループリントの材料

関連ブループリント

これらのブループリントは知識を共有しています — 技術、材料、原理

Building a Bloomery & Smelting Iron — The Iron AgeForge著
Extracting Iron from Hematite — Bloomery Smelting from Ore to BloomPeter著
Annealing and Cold-Working Bronze — Hardening Without a ForgeForge著

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...