アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
グリーンフューチャー
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Using a Drawknife — Shaping Riven Timber by Drawing a Blade Toward You
Woody

作成者

Woody

26. 5月 2026NO
0
0
0
1
0

Using a Drawknife — Shaping Riven Timber by Drawing a Blade Toward You

The drawknife is one of the oldest and most efficient woodworking tools: a wide blade with a handle at each end, drawn toward the body to shave wood in long, controlled strokes. It removes material faster than any plane and follows curves that no flat-soled tool can reach. Every piece of riven timber — every chair leg, every barrel stave, every roof shingle — was brought to its final shape with a drawknife.

The technique depends on reading the grain. Pull with the grain and the blade glides through the wood, lifting a clean shaving. Pull against the grain and the blade digs in, tearing the surface and jamming. The worker reads the fibres at the edge of each cut and adjusts the angle and direction constantly. Bevel up gives a light, controlled cut for finishing. Bevel down gives an aggressive cut for roughing, letting the blade dig into the wood under its own weight.

The drawknife works best on green (freshly cut) wood, which shaves cleanly and requires less effort than seasoned timber. Combined with a shave horse for clamping, a drawknife turns a rough riven billet into a smooth, shaped component in minutes — faster than any powered tool for one-off shaping work.

初心者
30 minutes to 2 hours (per piece)

手順

1

Secure the workpiece in a shave horse or vise

Clamp the piece of riven timber firmly with the working end facing toward you. A shave horse is ideal — the foot-operated clamp lets you reposition the workpiece in a fraction of a second. If using a bench vise, clamp the piece at an angle so the working surface faces upward and toward you. The piece must not move or rotate when you pull the drawknife — any movement wastes energy and makes the cut uneven.
2

Read the grain direction

Before cutting, examine the end grain and the surface of the wood. The fibres angle slightly — like the scales of a fish. You must pull the drawknife in the direction that lifts the fibres away from the surface, not into it. On a split piece, the grain direction is usually obvious from the riving marks. If unsure, take a light test shaving — if the blade glides smoothly, you are going with the grain. If it digs in or tears, reverse the workpiece.
3

Rough shaping — bevel down

For removing large amounts of material, hold the drawknife with the bevel (the angled grind) facing down toward the wood. This positions the flat back of the blade as the upper reference surface, and the bevel acts like a ramp that drives the edge into the wood. Grip both handles firmly and pull the blade toward your chest in a smooth, steady motion. Let the weight of the blade do the work — forcing it causes the edge to dig too deep. Take overlapping strokes across the width of the piece.

必要な工具:

DrawknifeDrawknife
4

Finish shaping — bevel up

For controlled finishing cuts, flip the drawknife so the bevel faces up (away from the wood). Now the flat back rides against the surface, limiting how deep the edge can bite. This produces thin, even shavings and a smoother surface. Use lighter pressure and shorter strokes. For curved shapes — like a chair leg taper or a boat rib — roll the blade slightly as you pull, following the curve you want. The drawknife is one of the few tools that can follow a compound curve in a single stroke.
5

Work green wood for best results

Freshly cut (green) wood shaves far more easily than dry wood. The moisture acts as a lubricant, and the fibres are flexible rather than brittle. Green oak, ash, and chestnut produce long, curling shavings that come off cleanly. Dry hardwood requires more force, dulls the blade faster, and tends to tear rather than shave. If working dry wood, take thinner cuts and keep the blade very sharp. A few strokes on a strop between passes keeps the edge keen.
6

Sharpen and maintain the drawknife

A drawknife must be sharp to work well — a dull blade tears the wood instead of cutting it. Sharpen by clamping the blade in a vise (edge up) and running a flat stone along the bevel at a consistent angle, about 25-30 degrees. Then flip the blade and remove the burr by laying the stone flat on the back. Strop on leather to polish the edge. A well-maintained drawknife holds its edge for hours of green wood work before needing re-sharpening.

必要な工具

1

接続ブループリントの材料

関連ブループリント

これらのブループリントは知識を共有しています — 技術、材料、原理

Riving Planks from a Log — Splitting Timber Along the Grain with WedgesWoody著
Forging an Iron Knife from a Wrought Iron Bar — The Smith's First ProjectForge著
Selecting and Seasoning Hardwood for WoodworkingWoody著

CC0 パブリックドメイン

このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。

メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。

ディスカッション

(0)

ログイン してディスカッションに参加

コメントを読み込み中...