アート
美容とウェルネス
工芸
文化と歴史
エンターテインメント
環境
食品と飲料
リバースエンジニアリング
科学
スポーツ
テクノロジー
ウェアラブル
Whirl-Frame Air Dasher Churn: Free Wheels Spun by the Milk Inside a Revolving Frame
Routzahn put free-turning wheels inside his dasher so the milk itself would spin them.
Nathaniel Routzahn of Middletown, Maryland, received US 7,199, dated 19 March 1850, for a churn-dasher of two L-shaped tubes of triangular section, running from near the cover down and in to the spindle, their horizontal arms perforated "through which air enters the milk during the revolution of the dasher." Between each upright arm and the axis, standards carry "whirls B, or wheels having inclined spokes," free to turn in planes through the axis. A bevel wheel and pinion turn the dasher fast, and "the friction thus produced by the whirls greatly facilitates the separation of the butter."
This rung estimates how the whirls spin, then prints the hollow frame and two whirls, fits them in a bucket, and makes butter.
中級者
About 4 hours, plus printing
手順
1
1
How the whirls spin
How the whirls spin
Jupyter ノートブックを読み込み中…
2
2
Beaters that turn on their own axes before it
Beaters that turn on their own axes before it
The embedded blueprint gears its rollers to a fixed wheel. Routzahn's whirls have no gearing: the milk spins them.
3
3
Read US 7,199
Read US 7,199
"The dasher thus receives a rapid rotating motion, and the whirls in passing through the milk are rapidly turned by its pressure upon the inclined faces of their arms which reacting upon the milk through which they pass, subdivides the whole mass and puts it in violent agitation, during which air is supplied through the outer tubes."
4
4
Print the parts
Print the parts
Print the frame flat on its side in one piece with supports: two hollow triangular L-tubes, perforated along their horizontal arms and open at the top, the top bar, and standards for the whirls. Print two whirls and the crank arm. Print in PETG at 0.2 mm layers, 30 % infill, 4 walls; wash before first use.
このステップの材料:
PETGフィラメント1 個必要な工具:
FDM 3D プリンター5
5
Print the frame
6
6
Print the whirl
7
7
Print the crank arm
8
8
Hang the whirls
Hang the whirls
Set each whirl between its standards and pass a 3 mm stainless rod through the standards and the whirl's hub as its axle; it must spin freely. Blow through each tube's top to check the arm holes are clear.
このステップの材料:
軟鋼丸棒1 個必要な工具:
金切りのこ（ハクソー）
紙やすり9
9
Spindle and crank
Spindle and crank
Pass a 10 mm square hardwood spindle through the frame's hubs and glue it. Stand it in a seat drilled in the centre of a food-grade bucket's floor, through a plywood lid, and glue the crank arm and a dowel handle on top. Keep the tubes' open tops above the cream.
このステップの材料:
堅木のダボ1 個
20 リットルのバケツ1 個
合板1 個
木工用接着剤1 個必要な工具:
コードレスドリル
ドリルビットセット
手のこぎり10
10
The build in 3D
The build in 3D
FreeCAD model of this build, not of the patent: the bucket cut away to show the frame of two triangular L-tubes on the spindle, their perforated horizontal arms, and a free whirl on its axle between standards in each half.
11
11
Crank and make butter
Crank and make butter
Let the heavy cream stand until it reaches about 15 °C, checked with the thermometer. Pour in 2 litres, below the tubes' open tops. Crank steadily and watch the whirls spin; time until the butter comes. Pour off the buttermilk, add cold water, churn a little and pour off again until it runs clear; work in a pinch of salt and weigh the butter.
このステップの材料:
生クリーム2000 ml
粗い海塩1 個
水1 個必要な工具:
差しっぱなしのプローブ温度計
ストップウォッチ
デジタルキッチンスケール
ステンレス鋼の大きな混ぜ鉢12
12
Whirls that won't spin, cream in the tubes
Whirls that won't spin, cream in the tubes
Whirl-frame air dasher troubleshooting.
Flow
Loading...
13
13
History and honest limits
History and honest limits
**Nathaniel Routzahn** of Middletown, Frederick County, Maryland, received US 7,199, dated 19 March 1850. He did not limit himself to the bevel wheel and pinion: "a belt running on pulleys, or an ordinary cog wheel and pinion can be used for the same purpose." He claimed the combination of the whirls with the revolving frame dasher.
**Honest limits.** Our crank turns the spindle directly, without his bevel gearing, so the frame and whirls turn slower; printed parts and a bucket stand in for his. The notebook gives an upper bound. FDM prints hold food in their layer lines, so wash well and replace when worn. Your times and weights are the result.
材料
9- 1 個プレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
- 2000 mlプレースホルダー
- 1 個プレースホルダー
- 1 個プレースホルダー
必要な工具
10- プレースホルダー
- プレースホルダー
- プレースホルダー
- 1 vendor sell this, none ship to you yetプレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
- プレースホルダー
設計ファイル
4この設計図で作るもの
関連ブループリント
これらのブループリントは知識を共有しています — 技術、材料、原理
CC0 パブリックドメイン
このブループリントはCC0で公開されています。許可を求めずに、自由にコピー、修正、配布、あらゆる目的で使用できます。
メイカーを応援するには、ブループリント経由で製品を購入してください。メイカーには メイカーコミッション がベンダーにより設定されています。または、このブループリントの新しいイテレーションを作成し、自分のブループリントにコネクションとして含めて収益を共有できます。