Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)
Tinny

Imeundwa na

Tinny

13. Novemba 2026US
7
0
0
0
0

Canteen From Two Pie Plates: Rims Soldered Together, a Screw-Cap Neck in the Edge (Boy Mechanic, 1919)

A canteen "for the camper or hiker", sent to The Boy Mechanic (1919) by J. R. Townsend of Itasca, Texas: two nickel-plated pie plates soldered rim to rim, the screw-capped neck of a metal-polish can soldered over an opening in the edge, and two wire loops for the snap hooks of a shoulder strap. The book gives no sizes: the plates set the size.
Mwanzo
About 2 hours

Maagizo

1

Read The Boy Mechanic

"Two good-quality pie plates were soldered at their edges to form a water-tight container." (J. R. Townsend, Itasca, Texas.)
2

Solder the plates together

Take two good-quality nickel-plated pie plates of the same size. Clean the rims, set them face to face, and solder them together all round the edge so the joint is water-tight. Use lead-free solder: this holds drinking water (our choice; the book only says solder).

Vifaa kwa hatua hii:

Sahani ya kuokea paiSahani ya kuokea pai2 vipande
Rambi ya mabomba bila risasiRambi ya mabomba bila risasi1 kipande
FluksiFluksi1 kipande

Zana zinazohitajika:

Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
Tupa ya chumaTupa ya chuma
3

Cut the neck off the can

Take a small metal-polish can with a screw cap. As the book's drawing shows, cut off its sloping top with the threaded neck, and trim the cut edge.

Vifaa kwa hatua hii:

Kopo la batiKopo la bati1 kipande

Zana zinazohitajika:

Mkasi mzito wa batiMkasi mzito wa bati
Tupa ya chumaTupa ya chuma
4

Cut the opening and fit the neck

Cut an opening in the edge of the canteen to suit the neck. Fit the neck carefully over it and solder it all round.

Vifaa kwa hatua hii:

Rambi ya mabomba bila risasiRambi ya mabomba bila risasi1 kipande
FluksiFluksi1 kipande

Zana zinazohitajika:

Kekee cha mkonoKekee cha mkono
Tupa ya chumaTupa ya chuma
Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
5

Solder on the strap loops

Bend two short pieces of wire into loops and solder one at each side of the screw cap, as loops for the snap hooks of the shoulder strap.

Vifaa kwa hatua hii:

Waya wa chuma uliovutwa kwa bambaWaya wa chuma uliovutwa kwa bamba1 kipande
Rambi ya mabomba bila risasiRambi ya mabomba bila risasi1 kipande
FluksiFluksi1 kipande

Zana zinazohitajika:

Koleo la Mdomo BapaKoleo la Mdomo Bapa
Pasi ya Umeme ya KulehemuPasi ya Umeme ya Kulehemu
6

Fit the strap and test

Put a snap hook on each end of a shoulder strap and hook them into the loops. Fill the canteen with water, screw on the cap and check every joint for leaks (our test), then rinse it before use.

Vifaa kwa hatua hii:

Ukanda wa NgoziUkanda wa Ngozi1 kipande
Ndoano ya springiNdoano ya springi2 vipande

Zana zinazohitajika:

Maji baridiMaji baridi
7

Troubleshooting

Canteen troubleshooting.

Flow

Loading...
8

History and honest limits

From **The Boy Mechanic, Book 3**, edited by H. H. Windsor, Popular Mechanics, Chicago, 1919 (Project Gutenberg 71856), "How to Make a Canteen", sent in by J. R. Townsend of Itasca, Texas. The book gives no sizes and names no tools; the lead-free solder, the tools, the strap material and the leak test are ours.

Vifaa

7

Zana Zinazohitajika

6

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...