Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI

Ski Sled: Two 10 ft Ash Ski Runners With a Rocker, Under a Three-Board Top (Boy Mechanic, 1919)
George J. Egelberg's ski sled from The Boy Mechanic, Book 3 (1919): "built low and wide so that it will not tip easily", on two 10 ft by 6 in ash runners boiled and bent like skis, set on knee blocks with a slight rocker, and topped with three 6 in boards.
Kati
About 2 days
Maagizo
1
1
His sizes, and the rocker
His sizes, and the rocker
Inapakia daftari la Jupyter…
2
2
Read The Boy Mechanic, Book 3
Read The Boy Mechanic, Book 3
"The skis, or runners, are cut 10 ft. long and 6 in. wide, from 1-in. ash boards that are straight-grained."
3
3
Thin the bend
Thin the bend
Cut two runners 10 ft long and 6 in wide from straight-grained 1 in ash. Where the curve will be, plane about 1/4 in off the upper side, but not at the very tip, so the skis bend more easily.
Vifaa kwa hatua hii:
Ubao wa Mti Mgumu2 vipandeZana zinazohitajika:
Msumeno wa mkono
Randa ya mkono
Tepi ya kupimia
Penseli4
4
Boil and bend
Boil and bend
If steaming is not handy, boil the skis with at least 1-1/2 ft of the points under water and the vessel covered so little steam escapes, for at least one hour. Take them out, put them side by side in the bending blocks at once and bend with slow, even pressure; weight the long ends and leave them 8 or 10 hours to dry. Sharpen the points after bending.
Vifaa kwa hatua hii:
Ubao wa msonobari1 kipandeZana zinazohitajika:
Sufuria Kubwa
Kibano cha upau
Randa ya mkono5
5
Set the blocks and top
Set the blocks and top
For a slight rocker, make the centre knee block 6 in high and the two end blocks 5-1/2 in. Run a 1/4 in flat-head bolt through the ski, the block and the cross strip, countersinking the heads in the running surface. Make the top of three 6 in boards fastened to the crosspieces, and brace the ski tips with a 2 in strip.
Vifaa kwa hatua hii:
Ubao wa Mti Mgumu1 kipande
Ubao wa msonobari3 vipande
Bolti ya kichwa cha duara6 vipande
Washa bapa6 vipande
Parafujo za mbao1 kipandeZana zinazohitajika:
Msumeno wa mkono
Kekee cha mkono
Seti ya Ncha za Kupanua Matundu
Nyundo6
6
Troubleshooting
Troubleshooting
Ski sled troubleshooting.
Flow
Loading...
7
7
History and honest limits
History and honest limits
From "A Ski Sled" by George J. Egelberg, in **The Boy Mechanic, Book 3**, Popular Mechanics, 1919 (Project Gutenberg 71856; checked on the archive.org scan boymechanic0003unse, p. 41). The bending-block shape and knee pieces come from his drawing. The tools and metric figures are ours.
Vifaa
5- 2 vipandeKishikilia Nafasi
- 3 vipandeKishikilia Nafasi
- 6 vipandeKishikilia Nafasi
- 6 vipandeKishikilia Nafasi
- 1 kipandeKishikilia Nafasi
Zana Zinazohitajika
9- Kishikilia Nafasi
- Kishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- 1 vendor sell this, none ship to you yetKishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
- Kishikilia Nafasi
Mchoro huu unatengeneza
Blueprint zinazohusiana
Blueprint hizi zinashiriki maarifa — mbinu, vifaa au kanuni
CC0 Umma Wote
Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.
Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.


