Ushirikiano
SANAA
UREMBO NA USTAWI
UJANJA
UTAMADUNI NA HISTORIA
BURUDANI
MAZINGIRA
CHAKULA NA VINYWAJI
UHANDISI WA KINYUME
SAYANSI
MICHEZO
TEKNOLOJIA
VAZI
Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)
Woody

Imeundwa na

Woody

14. Novemba 2026NO
7
0
0
0
0

Turner's Pole Lathe with Puppets, Screw Centre and Treadle (Moxon, 1680)

The workshop pole lathe of Joseph Moxon's Mechanick Exercises: legs and twin cheeks bolted square, sliding puppets wedged through the bed, a fixed steel-pointed pike and an adjustable screw centre, a hinged treadle with a cross-treadle, and a fir pole pinned to the ceiling for the spring.
Juu
Two to three days

Maagizo

1

His sizes

Inapakia daftari la Jupyter…
2

Read Mechanick Exercises

"The Lathe is described in Plate 12. A. This Machine is so vulgarly known..."
3

Legs and cheeks

Set up two legs about 2 ft 10 in (86 cm) high, plumb, each with a tenon on top as thick as the gap you want between the two cheeks. Lay a cheek each side of the tenons, level, and fix them: pinned, or better with an iron bolt whose square neck sits in a square hole in the near cheek, drawn up by a nut. Brace legs and cheeks to the floor and walls so nothing trembles.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe1 kipande
Bolti ya kichwa cha duaraBolti ya kichwa cha duara1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Patasi ya kutoboa tundu la kiungoPatasi ya kutoboa tundu la kiungo
Nyundo ya mbaoNyundo ya mbao
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
4

Puppets

Make two (or two or three pairs of) square puppets, strong rather than weak and as short as your work allows: the centres must stand a little more than half the work's diameter above the cheeks. Give each a tenon at the foot that slides in the gap between the cheeks, with a mortise through it below the cheeks for a tapering wedge, driven with a mallet to clamp the puppet down.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe1 kipande
Kabari la mbao gumuKabari la mbao gumu1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Patasi ya kutoboa tundu la kiungoPatasi ya kutoboa tundu la kiungo
Nyundo ya mbaoNyundo ya mbao
5

Pike and screw centre

Near the top of one puppet fix a strong iron pike with a tempered steel point. Through the other fit an iron screw in a nut in the puppet, also with a steel point, both points in one straight line facing each other. Put an iron handle 7-8 in long with a knob at each end through the screw head. Cut the puppets to square shoulders just below the pikes to carry the rest.

Vifaa kwa hatua hii:

Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande
Kipande cha mraba cha feleji ya zanaKipande cha mraba cha feleji ya zana1 kipande

Zana zinazohitajika:

Fua ya mhunziFua ya mhunzi
FuaweFuawe
Seti ya kukata nyuzi za skrubuSeti ya kukata nyuzi za skrubu
Ndoo ya kupoza chumaNdoo ya kupoza chuma
6

Rest and oil horn

Make the rest a square piece 1-1.5 in thick, 2-2.5 in broad, a little longer than the gap between the puppets. Hang a horn tip down on the outside of the right-hand puppet near the top, filled with oil, with a wooden cover and button carrying an iron wire that reaches nearly to the bottom, to oil the centre holes.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe1 kipande
Pembe ya ng'ombePembe ya ng'ombe1 kipande
Waya wa chuma uliovutwa kwa bambaWaya wa chuma uliovutwa kwa bamba1 kipande
Mafuta ya mashineMafuta ya mashine1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
7

Treadle and cross-treadle

Make a treadle about 2.5 in broad, 1 in thick and 3 ft (up to 4 ft) long. Nail its back end to the floor with a piece of leather, 1-1.5 ft behind the lathe and midway between the legs, so the front reaches 1.5-2 ft past the front of the lathe. Cut a square notch 1.5 in wide and 2 in long in the far end for winding the string. Fix an iron pin about 0.5 in thick, standing 1.5-2 in up, in the middle; under the cheeks fix a cross-treadle with a row of holes 2-3 in apart to take the pin.

Vifaa kwa hatua hii:

Ubao wa mwaloni mweupeUbao wa mwaloni mweupe1 kipande
Ukanda wa NgoziUkanda wa Ngozi1 kipande
Misumari ya ChumaMisumari ya Chuma1 kipande
Ufito wa chuma kilichofuliwaUfito wa chuma kilichofuliwa1 kipande

Zana zinazohitajika:

Msumeno wa mkonoMsumeno wa mkono
NyundoNyundo
Kekee cha mkono chenye nchaKekee cha mkono chenye ncha
8

Pole and string

Use a fir pole, thick or thin to suit the work; if it is too stiff, thin its upper and under sides with a draw-knife. Pin the thick end to a ceiling timber with one nail so it pivots. About a foot away nail two cheeks to the joists with a batten across their foot to carry the pole. Run the string from the pole's thin end, round the work, to the treadle.

Vifaa kwa hatua hii:

Mti wa mbaoMti wa mbao1 kipande
KambaKamba1 kipande
Misumari ya ChumaMisumari ya Chuma1 kipande
Ubao wa mwaloni mweupeUbao wa mwaloni mweupe1 kipande

Zana zinazohitajika:

Kisu cha KuvutaKisu cha Kuvuta
NyundoNyundo
9

Troubleshooting

Pole lathe troubleshooting.

Flow

Loading...
10

History and honest limits

From Joseph Moxon, **Mechanick Exercises**, Numb. X, Turning (1680), pp. 176-185 and Plate 12 (checked on the archive.org scan mechanickexercis00moxo). He gives no sizes for cheeks, puppets or pole; metric and the wood choices are ours.

Vifaa

12

Zana Zinazohitajika

10

CC0 Umma Wote

Mchoro huu umetolewa chini ya CC0. Uko huru kunakili, kubadilisha, kusambaza, na kutumia kazi hii kwa madhumuni yoyote, bila kuomba ruhusa.

Saidia Mtengenezaji kwa kununua bidhaa kupitia Mchoro wao ambapo wanapata Kamisheni ya Mtengenezaji iliyowekwa na Wachuuzi, au unda marudio mapya ya Mchoro huu na uiunganishe kama kiungo katika Mchoro wako kuchangia mapato.

Majadiliano

(0)

Ingia kujiunga na majadiliano

Inapakia maoni...