សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
អនាគតបៃតង
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Blinking an LED with LilyPad Arduino
Ed

បង្កើតដោយ

Ed

13. កក្កដា 2026FI
0
0
0
0
0

Blinking an LED with LilyPad Arduino

Step up from a plain sewn circuit to a sewable computer. The LilyPad Arduino is a washable microcontroller you program from your PC, then run on a coin cell — so your fabric can blink, fade and react on its own. This project sews an LED to the board and uploads the classic 'blink' sketch: the gateway to every sensor-driven wearable that follows.

មធ្យម
1 hour

ការណែនាំ

1

Sew the LilyPad Arduino and an LED

Sew a LilyPad Arduino Simple board and a LilyPad LED onto felt with conductive thread: the LED's + tab to numbered pin 5, and the LED's - tab to the board's - tab. Loop 3–4 times through each hole, trim tails, and keep the two lines from crossing.

Materials for this step:

LilyPad Arduino Simple BoardLilyPad Arduino Simple Board1 piece
LilyPad LED - 5 pcsLilyPad LED - 5 pcs1 pack
Conductive Thread - 60g (Stainless Steel)Conductive Thread - 60g (Stainless Steel)1 spool
Hand Sewing Needles (Assorted, 30-Pack)Hand Sewing Needles (Assorted, 30-Pack)1 pack
Wool Felt SheetWool Felt Sheet1 sheet
2

Connect the FTDI programmer

Plug a LilyPad FTDI Basic Breakout onto the board's 6-pin programming header (line up GND to GND, DTR to DTR) and connect it to your computer with a USB cable. Install the free Arduino IDE, then choose the LilyPad Arduino board and the FTDI's serial port under Tools.

Materials for this step:

LilyPad FTDI Basic Breakout - 5VLilyPad FTDI Basic Breakout - 5V1 piece
SparkFun Cerberus USB Cable - 1.8 meterSparkFun Cerberus USB Cable - 1.8 meter1 piece

Tools needed:

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the blink sketch

Paste this sketch into the Arduino IDE and click Upload. It flashes the LED on pin 5 on and off twice a second.

lilypad_blink.inoarduino
// Blink an LED sewn to a LilyPad Arduino
// The LED's + tab is stitched to pin 5, its - tab to the board's - (GND).

const int LED_PIN = 5;   // LilyPad LED sewn to pin 5

void setup() {
  pinMode(LED_PIN, OUTPUT);   // pin 5 drives the LED
}

void loop() {
  digitalWrite(LED_PIN, HIGH); // LED on
  delay(500);                  // wait half a second
  digitalWrite(LED_PIN, LOW);  // LED off
  delay(500);                  // wait half a second
}

// TRY THIS:
// - delay(100) for fast blinking, delay(2000) for slow
// - different ON and OFF times: HIGH delay(800), LOW delay(200)
4

Go wireless on a coin cell

Unplug the FTDI. Sew a LilyPad coin-cell battery holder to the board — + tab to +, - tab to - — and drop in a CR2032. Switch it on and the LED blinks on its own, no computer attached. Your fabric now runs its own program.

Materials for this step:

LilyPad Coin Cell Battery Holder - w/Switch - 20mmLilyPad Coin Cell Battery Holder - w/Switch - 20mm1 piece
CR2032 Coin Cell BatteryCR2032 Coin Cell Battery1 piece
5

Experiment

Re-attach the FTDI and change the sketch: adjust the delays for a heartbeat rhythm, or sew a second LED to another pin and blink them in turn. This is the base every LilyPad sensor project builds on.

សម្ភារៈ

9

ឧបករណ៍ចាំបាច់

1
Estimated Total
$90.00

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

Sewing a LilyPad LED Circuitដោយ Ed
Blinking LED — Your First Arduino Projectដោយ Admiral OOM

Related blueprints

Other builds that share materials, tools, or techniques with this one.

Using an LCD — SIK Circuit 15electronics
Sewing a LilyPad LED Circuitelectronics
Making a LilyPad Night-Lightelectronics
Making a Motion-Reactive LilyPad Patchelectronics
Making a Sound-Triggered LilyPad Patchelectronics
Making a Color-Changing LilyPad Patchelectronics

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...