សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Building a Carbon Monoxide Detector
Ed

បង្កើតដោយ

Ed

13. កក្កដា 2026FI
48
0
0
0
0

Building a Carbon Monoxide Detector

Build a circuit that senses carbon monoxide (CO) — the invisible, odourless gas from any incomplete combustion — and raises an alarm when it rises. An MQ-7 sensor gives the Arduino a reading that climbs with CO; the code compares it to a clean-air baseline and triggers a buzzer and red LED. A great way to learn gas sensing — but read the safety note: this is a demonstration, NOT a certified life-safety CO alarm.

មធ្យម
1-2 hours

ការណែនាំ

1

Wire the sensor, buzzer and LED

On the breadboard: MQ-7 VCC to Arduino 5V, GND to GND, and its analog output (AOUT) to Arduino A0. Active buzzer + to pin 8, - to GND. Red LED anode to pin 7 through a 330 Ω resistor, cathode to GND.

សម្ភារៈសម្រាប់ជំហាននេះ៖

Arduino Uno R3Arduino Uno R31 ដុំ
Carbon Monoxide Sensor - MQ-7Carbon Monoxide Sensor - MQ-71 ដុំ
Active Buzzer Module (5V, 5-Pack)Active Buzzer Module (5V, 5-Pack)1 ដុំ
LED - Basic 5mmLED - Basic 5mm1 ដុំ
Resistor 330 Ohm 1/6 Watt PTH - 20 packResistor 330 Ohm 1/6 Watt PTH - 20 pack1 ដុំ
BreadboardBreadboard1 ដុំ
Jumper Wires (Male-to-Male)Jumper Wires (Male-to-Male)1 កញ្ចប់
2

Connect and open the IDE

Plug the Arduino into your computer with the USB cable, open the Arduino IDE, and select Arduino Uno and its serial port.

សម្ភារៈសម្រាប់ជំហាននេះ៖

USB-B CableUSB-B Cable1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

Computer with Arduino IDEComputer with Arduino IDE
3

Upload the detector sketch

Paste this sketch and upload. It warms the sensor for two minutes, records a clean-air baseline, then sounds the buzzer and lights the LED whenever the reading climbs above that baseline.

co_detector.inoarduino
// Carbon monoxide INDICATOR using an MQ-7 sensor.
// NOT a certified life-safety alarm - see the blueprint's safety note.
// MQ-7 analog output on A0; buzzer on pin 8; red warning LED on pin 7.

const int MQ7_PIN = A0;
const int BUZZER_PIN = 8;
const int LED_PIN = 7;

int cleanAirValue = 0;          // baseline, measured at startup
const int ALARM_MARGIN = 150;   // how far above baseline triggers the alarm

void setup() {
  pinMode(BUZZER_PIN, OUTPUT);
  pinMode(LED_PIN, OUTPUT);
  Serial.begin(9600);

  Serial.println("Warming up the MQ-7 (2 min) in clean air...");
  delay(120000);                // 2-minute warm-up
  cleanAirValue = analogRead(MQ7_PIN);
  Serial.print("Clean-air baseline: ");
  Serial.println(cleanAirValue);
}

void loop() {
  int reading = analogRead(MQ7_PIN);
  Serial.println(reading);

  if (reading > cleanAirValue + ALARM_MARGIN) {
    digitalWrite(LED_PIN, HIGH);      // CO above baseline -> alarm
    digitalWrite(BUZZER_PIN, HIGH);
  } else {
    digitalWrite(LED_PIN, LOW);
    digitalWrite(BUZZER_PIN, LOW);
  }
  delay(500);
}
4

Warm up, baseline and test

Power it in fresh air and let the 2-minute warm-up set the clean-air baseline (a brand-new MQ-7 also needs a longer 24–48 h burn-in before its readings settle). Then hold a small CO source nearby in a ventilated room — the smoke from a just-blown-out match works — and the buzzer and LED should trigger. Change ALARM_MARGIN to make it more or less sensitive.

5

Important safety limits

This is a LEARNING project and, at best, a supplementary indicator — it is NOT a certified life-safety device. A hobby MQ-7 gives a relative reading, not a calibrated ppm; it drifts over time and needs regular re-baselining, and it also responds to smoke and other gases. Carbon monoxide is invisible, odourless and can be fatal: for real protection always use a UL- or EN-certified CO alarm. Never rely on this circuit to keep anyone safe.

សម្ភារៈ

8

ឧបករណ៍ចាំបាច់

2
សរុបប៉ាន់ស្មាន
អ្វីដែលអ្នកផលិតបានទិញ។ សម្ភារៈដែលបង្ហាញដោយគ្មានតម្លៃ គឺទិញនៅកន្លែងដែលអ្នករកបាន។
$57.80

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

Building an Ultrasonic Parking Sensor

Building an Ultrasonic Parking Sensor

ដោយ EdFI

ឌីជីថល

31
0
0
0
0
0
Blinking LED — Your First Arduino Project
BLUEPRINT NFT

Blinking LED — Your First Arduino Project

ដោយ Admiral OOMNO

ឌីជីថល

485
2
1
7
0
0

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...