កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក

Fuller, Pritchel and Hot Setts: Steel Welded into a Split Iron Bar, with Twisted Rod or Withy Handles (Edwinson, 1886)
The smith's own top and bottom tools, from George Edwinson's farrier's chapter in Amateur Work (1886): an inch iron bar upset, split into a fork and a steel wedge welded in, then forged into a fuller, pritchel punch, curved or straight hot sett, or a square-tanged bottom sett; the pritchel itself from 1/2 in. square tool steel; handles of twisted iron rod or green withy.
កម្រិតខ្ពស់
A day at the forge for the set
ការណែនាំ
1
1
His proportions
His proportions
កំពុងផ្ទុកសៀវភៅ Jupyter…
2
2
Read Edwinson
Read Edwinson
"To make this tool, heat and upset the end of an inch bar of iron; then heat again and split with a sett."
3
3
Split the iron
Split the iron
Heat and upset the end of a 1 in. (25 mm) iron bar. Heat again and split it with a hot set into a fork 1 to 1 1/4 in. long by 3/4 in. wide (his fig. 108).
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដំបងដែកវាយ1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)
ញញួរធំ
ដែកកាត់ក្ដៅ
ដង្កៀបជាងដែក4
4
Weld in the steel
Weld in the steel
Heat the end of a steel bar of similar size and forge a wedge to fit the fork (fig. 109). Bring both to a welding heat and weld them well together.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកថែបរំលាយក្នុងឆ្នាំង1 ដុំ
ម្សៅបូរ៉ាក់1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)
ញញួរធំ
ដង្កៀបជាងដែក5
5
Forge the fuller
Forge the fuller
Cut off 2 in. of steel and 3 in. of iron for the tool. Forge the steel, with the iron behind it, into the fuller's rounded blade (fig. 102). Make the neck while it is still on the bar, then cut it off leaving a piece of iron for the head.
ឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)
ញញួរ
ដែកកាត់ក្ដៅ6
6
Same blank, other tools
Same blank, other tools
Pritchel punch: about 2 in. of iron and 1 in. of steel, shaped as fig. 103. Curved set: as the fuller but with a gouge-shaped blade (fig. 105). Top hot set: the same, with a chisel or wedge blade (fig. 106). Bottom set: a wedge of steel and iron, edge up, on a square tang that fits the anvil's square hole (fig. 107).
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដំបងដែកវាយ1 ដុំ
ដែកថែបរំលាយក្នុងឆ្នាំង1 ដុំ
ម្សៅបូរ៉ាក់1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)
ញញួរ
ញញួរធំ
ដង្កៀបជាងដែក7
7
Forge the pritchel
Forge the pritchel
Forge 1/2 in. (13 mm) square tool steel into the tapered pritchel (fig. 104), 6 in. (150 mm) long. It punches nail holes in hot iron, so it need not be hardened.
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកថែបឧបករណ៍ជាដុំមូល1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)
ញញួរ
ដង្កៀបជាងដែក8
8
Fit the handles
Fit the handles
Rod handle: twist 3/8 in. iron rod once round the neck and weld the two ends together (fig. 110). Withy handle: take a green or half-green hazel, willow, oak or withy rod about 3 ft long, twist the middle 8-9 in., wrap it once round the neck and bind the two ends with wire or a link (figs. 106, 111).
សម្ភារៈសម្រាប់ជំហាននេះ៖
ដែកថែបទន់មូល1 ដុំ
មែកអំបូរ (បត់បែន)1 ដុំ
លួសដែកទាញ1 ដុំឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ទាំងជល់ (កំណាត់ដែក)
ញញួរ
ដង្កៀបជាងដែក9
9
Harden the cutting tools (ours)
Harden the cutting tools (ours)
He gives no temper for these. Ours: harden and temper the set edges as for other hot-cutting tools, and cool them often in use.
ឧបករណ៍ដែលត្រូវការ៖
ឡជាងដែក
ធុងជ្រលក់ត្រជាក់10
10
Troubleshooting
Troubleshooting
Top-tool troubleshooting.
Flow
Loading...
11
11
History and honest limits
History and honest limits
From George Edwinson, "Smithing and Forging" VII, **Amateur Work, Illustrated**, vol. VI (1886-87), pp. 14-16 and figs. 101-111 (checked on the archive.org scan amateurworkillus06lond). He calls the top hot cutter a "sett"; we map it to the Hot Chisel head and the bottom sett to the Hot Cut Hardy head. Temper, metric figures and tools are ours.
សម្ភារៈ
7- 1 ដុំកន្លែងទុក
- កន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
- 1 ដុំកន្លែងទុក
ប្លង់នេះធ្វើ
ប្លង់ពាក់ព័ន្ធ
ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍
CC0 សាធារណៈ
ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។
គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។






