កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)
Forge

បង្កើតដោយ

Forge

13. វិច្ឆិកា 2026NO
7
0
0
0
0

Rack-and-Pinion Router With a Zero-Set Knob: Two Knobs on One Hollow Pinion, Set to Zero on the Work (Rees, 1969)

Spencer C. Rees of Pickens, South Carolina, received US 3,466,973, dated 16 September 1969, for The Singer Company. A rack screwed to the motor housing is moved by a pinion through a window in a box on the base. The pinion is a hollow shaft running in one bore through the box's two side lugs, with a knob at each end. One knob turns it. The other, a zero-set knob with graduations, slips on its sleeve against an O-ring, so it can be set to zero with the bit touching the work. One screw through the middle holds it all together. Only the pinion shaft was metal; the rest was moulded. We print every part in PETG round a small DC motor. The sizes are ours.
កម្រិតខ្ពស់
About 3 days

ការណែនាំ

1

What one turn of the knob does

កំពុងផ្ទុកសៀវភៅ Jupyter…
2

Read US 3,466,973

"The zero-set knob 40 has a reduced diameter portion 51 which carries circumferentially-spaced graduation marks 52 on its surface." "In the above-described structure it will be noted that the only metallic part required is the pinion shaft 37 which is a relatively simple two-diameter piece."
3

Print the base

The base 10: the split ring with clamp lugs, the box 28 for the rack with its two lugs 50 and stepped bore 33, the window 36, two legs 11 down to the plate 12 with its aperture, and two handle arms. Print it plate down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
ឯកសាររចនាSTLCC0 - Free
4

Print the motor housing

The housing 19: a tube for a 42 mm motor, 56 mm outside, a ledge with an 18 mm hole and two M4 holes, and two M3 holes for the rack. Print it ledge down. PETG, 0.2 mm layers, 40 % infill, 5 walls.
ឯកសាររចនាSTLCC0 - Free
5

Print the small parts

One plate: the rack 29 (module 1.5), the hollow pinion shaft 37 with its toothed (splined) part, bearing part and end ribs, the adjusting knob 38 with grooves, the flanged sleeve 39, the zero-set knob 40 with 20 graduations and an O-ring groove, and the cover plate 53 with its window 55 and mark 56. PETG, 0.2 mm layers, 40 % infill, 5 walls.
ឯកសាររចនាSTLCC0 - Free
6

Motor in the housing

Fit the collet adapter on the motor's shaft, stand the motor in the housing on its ledge and screw it down with two M4 screws; wire it through a toggle switch to the DC supply. Screw the rack to the housing's front with two M3 screws.

សម្ភារៈសម្រាប់ជំហាននេះ៖

សរសៃ PETGសរសៃ PETG1 ដុំ
ម៉ូទ័រអគ្គិសនីម៉ូទ័រអគ្គិសនី1 ដុំ
អាដាប់ទ័រកូឡេតសម្រាប់អ័ក្សម៉ូទ័រអាដាប់ទ័រកូឡេតសម្រាប់អ័ក្សម៉ូទ័រ1 ដុំ
វីសក្បាលរន្ធប្រាំមួយជ្រុងវីសក្បាលរន្ធប្រាំមួយជ្រុង2 ដុំ
វីសម៉ាស៊ីនវីសម៉ាស៊ីន2 ដុំ
កុងតាក់ដងបត់កុងតាក់ដងបត់1 ដុំ
ខ្សែតភ្ជាប់ខ្សែតភ្ជាប់1 ដុំ
បំពង់រួញដោយកម្តៅបំពង់រួញដោយកម្តៅ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនបោះពុម្ព 3D ប្រើខ្សែ (FDM)ម៉ាស៊ីនបោះពុម្ព 3D ប្រើខ្សែ (FDM)
ប្រភពថាមពលចរន្តផ្ទាល់ប្រភពថាមពលចរន្តផ្ទាល់
ដែកផ្សារសំណអគ្គិសនីដែកផ្សារសំណអគ្គិសនី
សំណុំកូនសោប្រាំមួយជ្រុងសំណុំកូនសោប្រាំមួយជ្រុង
ឈុតទួណឺវីសឈុតទួណឺវីស
ឧបករណ៍ដកសំណល់គែមឧបករណ៍ដកសំណល់គែម
7

Base and handles

Turn two hardwood handles 17 and bolt one to each arm with an M8 bolt. Slide the housing into the base with the rack in the box's channel, and put an M5 screw with a wing nut through the clamp lugs.

សម្ភារៈសម្រាប់ជំហាននេះ៖

ក្តារឈើរឹងក្តារឈើរឹង1 ដុំ
ការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុងការប្រមូលផ្ដុំប៊ូឡុងប្រាំមួយជ្រុង2 ដុំ
ខ្ចៅប្រាំមួយជ្រុងខ្ចៅប្រាំមួយជ្រុង3 ដុំ
វីសក្បាលរន្ធប្រាំមួយជ្រុងវីសក្បាលរន្ធប្រាំមួយជ្រុង1 ដុំ
ខ្ចៅស្លាបមេអំបៅខ្ចៅស្លាបមេអំបៅ1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ម៉ាស៊ីនកែងឈើម៉ាស៊ីនកែងឈើ
ស្វានឥតខ្សែស្វានឥតខ្សែ
សំណុំក្បាលខួងសំណុំក្បាលខួង
សោរបង្វិលកែតម្រូវបានសោរបង្វិលកែតម្រូវបាន
8

Pinion, knobs and cover

Push the pinion shaft through the box's bore from the right, its toothed part through the window meshing with the rack, its bearing part in the right lug. Fit the O-ring in the zero-set knob's groove, push the sleeve into the knob, and slide them onto the shaft's toothed end from the left, the sleeve in the left lug. Fit the adjusting knob on the right end, its grooves on the shaft's ribs. Pass a long M4 screw through knob, shaft and sleeve with a washer, into a nut in the sleeve, and tighten it until the knobs have only a little end play. Screw the cover over the box with two M3 screws.

សម្ភារៈសម្រាប់ជំហាននេះ៖

អូរីងអូរីង1 ដុំ
វីសក្បាលរន្ធប្រាំមួយជ្រុងវីសក្បាលរន្ធប្រាំមួយជ្រុង1 ដុំ
រ៉ុនដែលរាបស្មើរ៉ុនដែលរាបស្មើ1 ដុំ
ខ្ចៅប្រាំមួយជ្រុងខ្ចៅប្រាំមួយជ្រុង1 ដុំ
វីសម៉ាស៊ីនវីសម៉ាស៊ីន2 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

សំណុំកូនសោប្រាំមួយជ្រុងសំណុំកូនសោប្រាំមួយជ្រុង
ឈុតទួណឺវីសឈុតទួណឺវីស
9

Set zero and rout

Fit a bit. Loosen the clamp, turn the adjusting knob until the bit's tip touches the work, then turn the zero-set knob alone until its zero lines up with the cover's mark. Turn the adjusting knob to the depth wanted, read off the graduations, and clamp. Rout with both hands on the handles.

ឧបករណ៍ដែលត្រូវការ៖

សំណុំក្បាលម៉ាស៊ីនឆូតសំណុំក្បាលម៉ាស៊ីនឆូត
ក្តារឈើរឹងក្តារឈើរឹង
ឈ្នាប់ដងវែងឈ្នាប់ដងវែង
ជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញជញ្ជីងវាស់ឌីជីថល ៦ អ៊ីញ
វ៉ែនតាសុវត្ថិភាពវ៉ែនតាសុវត្ថិភាព
10

Troubleshooting

Rack and pinion router troubleshooting.

Flow

Loading...
11

History and honest limits

**Spencer C. Rees** of Pickens, South Carolina, assignor to The Singer Company, US 3,466,973, dated 16 September 1969, filed 8 January 1968. He claimed a rack on the motor housing, "a pair of lugs formed on the base in fixed spaced relation on opposite sides of the rack and having aligned cylindrical apertures", a hollow pinion shaft, an adjusting knob, a flanged sleeve, "a zero-set knob frictionally coupled to said sleeve", and "single fastening means" through them all. His pinion shaft was metal and the rest moulded; ours is all printed. His motor ran on mains; ours is a small DC motor. He gives no sizes; every size here is ours.

សម្ភារៈ

14

ឧបករណ៍ចាំបាច់

15

ឯកសាររចនា

3

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...