កិច្ចសហប្រតិបត្តិការ
សិល្បៈ
សម្រស់ និង សុខុមាលភាព
សិប្បកម្ម
វប្បធម៌ និង ប្រវត្តិសាស្ត្រ
ការកម្សាន្ត
បរិស្ថាន
ម្ហូប និង ភេសជ្ជៈ
វិស្វកម្មបញ្ច្រាស
វិទ្យាសាស្ត្រ
កីឡា
បច្ចេកវិទ្យា
ប្រដាប់ដែលស្លៀក
Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)
Bubbles

បង្កើតដោយ

Bubbles

14. វិច្ឆិកា 2026IT
5
0
0
0
0

Bulb Pipette Blown at the Lamp: a Closed Tube Drawn, Bulbed, Pierced and Joined to Two Stems (Soward, 1886)

Alfred Soward's lampwork bulb pipette from Amateur Work (1886), made like his thistle funnel: a 3/8 in. bore tube closed and drawn down onto a 1/8 in. stem, blown into a bulb, a thin second bulb blown and broken off the far side to leave a short neck, and a second stem drawn to a fine capillary tip joined on.
កម្រិតខ្ពស់
An hour once the basic operations are mastered

ការណែនាំ

1

Read Soward

"To make a pipette the process is very similar." (to the thistle funnel)
2

Prepare the tubes

Take glass tube of about 1/8 in. (3 mm) bore for the stems and about 3/8 in. (10 mm) bore for the bulb. Close the wide tube at one end in the form of his fig. 41 A, then soften it about an inch from the end and draw it down to the small tube's diameter.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់កញ្ចក់បំពង់កញ្ចក់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ចង្ក្រានប៊ុនសែនចង្ក្រានប៊ុនសែន
បំពង់ផ្លុំកញ្ចក់បំពង់ផ្លុំកញ្ចក់
3

Join the first stem

Cut the drawn, flask-shaped piece off with a file and fuse it to a length of the narrow tube: soften both ends, press them together, pull gently to reduce the thickened joint, and blow a gentle stream of air in.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់កញ្ចក់បំពង់កញ្ចក់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ចង្ក្រានប៊ុនសែនចង្ក្រានប៊ុនសែន
បំពង់ផ្លុំកញ្ចក់បំពង់ផ្លុំកញ្ចក់
4

Blow the bulb

Soften the flask part and blow it into a bulb through the stem.

ឧបករណ៍ដែលត្រូវការ៖

ចង្ក្រានប៊ុនសែនចង្ក្រានប៊ុនសែន
បំពង់ផ្លុំកញ្ចក់បំពង់ផ្លុំកញ្ចក់
5

Open the far end

Play the flame on the point opposite the stem (A in fig. 41) and blow a very thin second bulb with a strong blast. Break it away: it leaves a small projecting tube (B).

ឧបករណ៍ដែលត្រូវការ៖

ចង្ក្រានប៊ុនសែនចង្ក្រានប៊ុនសែន
បំពង់ផ្លុំកញ្ចក់បំពង់ផ្លុំកញ្ចក់
6

Draw and join the tip

Draw a second piece of narrow tube to a capillary end: thicken it in the flame, pull the hands apart, cut with a file and hold the cut end a moment in the flame. Join this stem to the projecting tube as before.

សម្ភារៈសម្រាប់ជំហាននេះ៖

បំពង់កញ្ចក់បំពង់កញ្ចក់1 ដុំ

ឧបករណ៍ដែលត្រូវការ៖

ដែកឆាប (ដែកឆាបដៃ)ដែកឆាប (ដែកឆាបដៃ)
ចង្ក្រានប៊ុនសែនចង្ក្រានប៊ុនសែន
បំពង់ផ្លុំកញ្ចក់បំពង់ផ្លុំកញ្ចក់
7

Troubleshooting

Pipette troubleshooting.

Flow

Loading...
8

History and honest limits

From Alfred W. Soward, "Glass-Blowing for Amateurs" IV, **Amateur Work, Illustrated**, vol. V (1886), pp. 173-176, figs. 39-41 (checked on the archive.org scan amateurworkillus05lond). He gives no volume or graduation: calibrate it by weighing water if you need one (see the graduated-pipette blueprint). Metric figures are ours.

សម្ភារៈ

1

ឧបករណ៍ចាំបាច់

3

ប្លង់ពាក់ព័ន្ធ

ប្លង់ទាំងនេះចែករំលែកចំណេះដឹង — បច្ចេកទេស សម្ភារៈ ឬគោលការណ៍

CC0 សាធារណៈ

ប្លង់នេះត្រូវបានចេញផ្សាយក្រោម CC0។ អ្នកមានសិទ្ធិចម្លង កែប្រែ ចែកចាយ និងប្រើប្រាស់ដោយមិនចាំបាច់សុំអនុញ្ញាត។

គាំទ្រអ្នកបង្កើតដោយទិញផលិតផលតាមរយៈប្លង់របស់ពួកគេ ដែលពួកគេទទួលបាន កម្រៃជើងសារអ្នកបង្កើត កំណត់ដោយអ្នកលក់ ឬបង្កើតកំណែថ្មីនៃប្លង់នេះ ហើយបញ្ចូលជាការតភ្ជាប់ក្នុងប្លង់របស់អ្នកដើម្បីចែករំលែកចំណូល។

ការពិភាក្សា

(0)

ចូល ដើម្បីចូលរួមពិភាក្សា

កំពុងផ្ទុកមតិ...